Skip to content

O
OpenXG-RAN
Commit a2a00d22 authored by Raphael Defosseux's avatar Raphael Defosseux
Browse files
Options

CI: Improvements on the COTS-UE bench script 

  * added banner to pipeline script
  * added parameters to Jenkins pipeline / python
    * xmlfile and test stage
  * eNB configuration files are located under ci-scripts/conf_files
    * no more correction of MNC
    * still correction of EPC / eNB IP addresses at runtime
    * Initialize_eNB_args is back using the proper "-O " syntax
  * Terminate stage is parallel as in FJU's original pipeline
  * Log collection stage is back fully parallel
  * Console as artifact an option
  * Check if terminate calls ended well, to be repeated at the end
  * Adding back iperf:
    * selection of iperf vs iperf3
    * adding some iperf testcases to test suite
  * Better enb launch
Signed-off-by: default avatarRaphael Defosseux <raphael.defosseux@eurecom.fr>
parent f911895b
Hide whitespace changes
Inline Side-by-side
Showing with 1321 additions and 177 deletions
ci-scripts/Jenkinsfile-tmp-ran
View file @ a2a00d22
//
// Comments
#!/bin/groovy
/*
* Licensed to the OpenAirInterface (OAI) Software Alliance under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership.
* The OpenAirInterface Software Alliance licenses this file to You under
* the OAI Public License, Version 1.1 (the "License"); you may not use this file
* except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.openairinterface.org/?page_id=698
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*-------------------------------------------------------------------------------
* For more information about the OpenAirInterface (OAI) Software Alliance:
* contact@openairinterface.org
*/
// Template Jenkins Declarative Pipeline script to run Test w/ RF HW
// Location of the python executor node shall be in the same subnet as the others servers
def pythonExecutor = params.pythonExecutor
// Location of the test XML file to be run
def testXMLFile = params.pythonTestXmlFile
// Name of the test stage
def testStageName = params.pipelineTestStageName
// Terminate Status
def termUE = 0
def termENB = 1
def termSPGW = 2
def termMME = 3
def termHSS = 4
def termStatusArray = new Boolean[termHSS + 1]
termStatusArray[termUE] = false
termStatusArray[termENB] = false
termStatusArray[termSPGW] = false
termStatusArray[termMME] = false
termStatusArray[termHSS] = false
def eNB_Repository
def eNB_Branch
def eNB_CommitID
pipeline {
// The node should be selected with a 'label' parameter
// trying to use NodeLabel plugin to pass it, currently failing to do so
agent {
label 'starsky'
label pythonExecutor
}
options {
disableConcurrentBuilds()
......@@ -17,16 +62,22 @@ pipeline {
// You can use them as template
/*
parameters {
//node-test parameters
string(name: 'pythonExecutor', defaultValue: 'nodea', description: 'Node where the pipeline - python scripts will be executed')
string(name: 'pythonTestXmlFile', defaultValue: 'enb_usrpB210_band7_50PRB.xml', description: 'Location of the Test XML to be run')
string(name: 'pipelineTestStageName', defaultValue: 'Test COTS-UE - OAI eNB - LTEBOX EPC', description: 'Naming of the Test Stage')
booleanParam(name: 'pipelineZipsConsoleLog', defaultValue: 'True', description: 'If true, the pipeline script retrieves the job console log, zips it and archives it as artifact')
//eNB parameters
string(name: 'eNB_IPAddress', defaultValue: '192.168.XX.XX', description: 'IP Address of eNB')
credentials(name: 'eNB_Credentials', defaultValue: 'XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX', credentialType: "Username with password", required: true, description: 'Credentials for eNB')
string(name: 'eNB_SourceCodePath', defaultValue: '/home/starsky/CI-enb', description: 'Full path of eNB source code')
string(name: 'eNB_SourceCodePath', defaultValue: '/tmp/CI-enb', description: 'Full path of eNB source code')
//EPC parameters
string(name: 'EPC_IPAddress', defaultValue: '192.168.XX.XX', description: 'IP Address of EPC')
string(name: 'EPC_Type', defaultValue: 'OAI', description: 'EPC type: OAI or ltebox')
string(name: 'EPC_Type', defaultValue: 'ltebox', description: 'EPC type: OAI or ltebox')
credentials(name: 'EPC_Credentials', defaultValue: 'XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX', credentialType: "Username with password", required: true, description: 'Credentials for EPC')
string(name: 'EPC_SourceCodePath', defaultValue: '/home/nano/CI_oai-cn/openair-cn', description: 'Full path of EPC source code')
string(name: 'EPC_SourceCodePath', defaultValue: '/tmp/CI-enb', description: 'Full path of EPC source code')
//ADB server parameters
string(name: 'ADB_IPAddress', defaultValue: '192.168.XX.XX', description: 'IP Address of ADB server')
......@@ -38,11 +89,24 @@ pipeline {
stage ("Verify Parameters") {
steps {
script {
echo '\u2705 \u001B[32mVerify Parameters\u001B[0m'
def allParametersPresent = true
if (params.CI_MASTER_NODE != null) {
echo "eNB CI parameter node : $params.CI_MASTER_NODE"
// It is already to late to check it
if (params.pythonExecutor != null) {
echo "eNB CI executor node : ${pythonExecutor}"
}
// If not present picking a default XML file
if (params.pythonTestXmlFile == null) {
// picking default
testXMLFile = 'xml_files/enb_usrpB210_band7_50PRB.xml'
} else {
echo "eNB CI master node : $NODE_NAME"
echo "Test XML file : ${testXMLFile}"
}
// If not present picking a default Stage Name
if (params.pipelineTestStageName == null) {
// picking default
testStageName = 'Template Test Stage'
}
if (params.eNB_IPAddress == null) {
......@@ -54,6 +118,26 @@ pipeline {
if (params.eNB_Credentials == null) {
allParametersPresent = false
}
// the following 3 parameters should be pushed by the master trigger
// if not present, take the job GIT variables (used for developing)
if (params.eNB_Repository == null) {
eNB_Repository = env.GIT_URL
} else {
eNB_Repository = params.eNB_Repository
}
echo "eNB_Repository : ${eNB_Repository}"
if (params.eNB_Branch == null) {
eNB_Branch = env.GIT_BRANCH
} else {
eNB_Branch = params.eNB_Branch
}
echo "eNB_Branch : ${eNB_Branch}"
if (params.eNB_CommitID == null) {
eNB_CommitID = env.GIT_COMMIT
} else {
eNB_CommitID = params.eNB_CommitID
}
echo "eNB_CommitID : ${eNB_CommitID}"
if (params.EPC_IPAddress == null) {
allParametersPresent = false
......@@ -84,61 +168,110 @@ pipeline {
}
}
}
stage ("Build eNB") {
stage ("Build and Test") {
steps {
script {
dir ('ci-scripts') {
try {
echo "\u2705 \u001B[32m${testStageName}\u001B[0m"
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.ADB_Credentials}", usernameVariable: 'ADB_Username', passwordVariable: 'ADB_Password']
]) {
sh "python3 main.py --mode=TesteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBRepository=${GIT_URL} --eNBBranch=${GIT_BRANCH} --eNBCommitID=${GIT_COMMIT} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath} --EPCIPAddress=${params.EPC_IPAddress} --EPCType=${params.EPC_Type} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password} --XMLTestFile=xml_files/build_enb_usrp_start_epc.xml"
sh "python3 main.py --mode=TesteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBRepository=${eNB_Repository} --eNBBranch=${eNB_Branch} --eNBCommitID=${eNB_CommitID} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath} --EPCIPAddress=${params.EPC_IPAddress} --EPCType=${params.EPC_Type} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password} --XMLTestFile=${testXMLFile}"
}
} catch (Exception e) {
sh "./ci-scripts/fail.sh"
currentBuild.result = 'FAILURE'
}
}
}
}
}
stage ("Test eNB - Band 7 - USRP210 - 5MHz") {
steps {
script {
dir ('ci-scripts') {
try {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.ADB_Credentials}", usernameVariable: 'ADB_Username', passwordVariable: 'ADB_Password']
]) {
sh "python3 main.py --mode=TesteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBRepository=${GIT_URL} --eNBBranch=${GIT_BRANCH} --eNBCommitID=${GIT_COMMIT} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath} --EPCIPAddress=${params.EPC_IPAddress} --EPCType=${params.EPC_Type} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password} --XMLTestFile=xml_files/enb_usrpB210_band7_50PRB.xml"
stage ("Terminate") {
parallel {
stage('Terminate UE') {
steps {
echo '\u2705 \u001B[32mTerminate UE\u001B[0m'
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.ADB_Credentials}", usernameVariable: 'ADB_Username', passwordVariable: 'ADB_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateUE --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password}"
}
}
post {
success {
script {
termStatusArray[termUE] = true
}
} catch (Exception e) {
//sh "./ci-scripts/fail.sh"
currentBuild.result = 'FAILURE'
}
}
}
}
}
stage ("Terminate All") {
steps {
script {
dir ('ci-scripts') {
try {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.ADB_Credentials}", usernameVariable: 'ADB_Username', passwordVariable: 'ADB_Password']
]) {
sh "python3 main.py --mode=TesteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBRepository=${GIT_URL} --eNBBranch=${GIT_BRANCH} --eNBCommitID=${GIT_COMMIT} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath} --EPCIPAddress=${params.EPC_IPAddress} --EPCType=${params.EPC_Type} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password} --XMLTestFile=xml_files/terminate_epc.xml"
stage('Terminate eNB') {
steps {
echo '\u2705 \u001B[32mTerminate eNB\u001B[0m'
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateeNB --eNBIPAddress=${params.eNB_IPAddress} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password}"
}
}
post {
success {
script {
termStatusArray[termENB] = true
}
}
}
}
stage('Terminate SPGW') {
steps {
echo '\u2705 \u001B[32mTerminate SPGW\u001B[0m'
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateSPGW --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCType=${params.EPC_Type} --EPCSourceCodePath=${params.EPC_SourceCodePath}"
}
}
post {
success {
script {
termStatusArray[termSPGW] = true
}
}
}
}
stage('Terminate MME') {
steps {
echo '\u2705 \u001B[32mTerminate MME\u001B[0m'
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateMME --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCType=${params.EPC_Type} --EPCSourceCodePath=${params.EPC_SourceCodePath}"
}
}
post {
success {
script {
termStatusArray[termMME] = true
}
}
}
}
stage('Terminate HSS') {
steps {
echo '\u2705 \u001B[32mTerminate HSS\u001B[0m'
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateHSS --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCType=${params.EPC_Type} --EPCSourceCodePath=${params.EPC_SourceCodePath}"
}
}
post {
success {
script {
termStatusArray[termHSS] = true
}
} catch (Exception e) {
//sh "./ci-scripts/fail.sh"
currentBuild.result = 'FAILURE'
}
}
}
......@@ -146,71 +279,110 @@ pipeline {
}
stage('Log Collection') {
parallel {
stage('Log Collection (eNB)') {
stage('Log Collection (eNB - Build)') {
steps {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password']
]) {
echo '\u2705 \u001B[32mLog Collection (eNB - Build)\u001B[0m'
sh "python3 ci-scripts/main.py --mode=LogCollectBuild --eNBIPAddress=${params.eNB_IPAddress} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath}"
echo '\u2705 \u001B[32mLog Transfer (eNB - Build)\u001B[0m'
sh "sshpass -p \'${eNB_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${eNB_Username}@${params.eNB_IPAddress}:${eNB_SourceCodePath}/cmake_targets/build.log.zip ./build.log.${env.BUILD_ID}.zip || true"
}
script {
if(fileExists("build.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "build.log.${env.BUILD_ID}.zip"
}
}
}
}
stage('Log Collection (eNB - Run)') {
steps {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password']
]) {
echo '\u2705 \u001B[32mLog Collection (eNB - Run)\u001B[0m'
sh "python3 ci-scripts/main.py --mode=LogCollecteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath}"
echo '\u2705 \u001B[32mLog Transfer (eNB - Run)\u001B[0m'
sh "sshpass -p \'${eNB_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${eNB_Username}@${params.eNB_IPAddress}:${eNB_SourceCodePath}/cmake_targets/enb.log.zip ./enb.log.${env.BUILD_ID}.zip || true"
}
script {
if(fileExists("enb.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "enb.log.${env.BUILD_ID}.zip"
}
}
}
}
stage('Log Collection (SPGW)') {
steps {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
echo '\u2705 \u001B[32mLog Collection (SPGW)\u001B[0m'
sh "python3 ci-scripts/main.py --mode=LogCollectSPGW --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type}"
echo '\u2705 \u001B[32mLog Transfer (SPGW)\u001B[0m'
sh "sshpass -p \'${EPC_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${EPC_Username}@${params.EPC_IPAddress}:${EPC_SourceCodePath}/scripts/spgw.log.zip ./spgw.log.${env.BUILD_ID}.zip || true"
}
script {
if(fileExists("spgw.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "spgw.log.${env.BUILD_ID}.zip"
}
}
}
}
stage('Log Collection (MME)') {
steps {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
echo '\u2705 \u001B[32mLog Collection (MME)\u001B[0m'
sh "python3 ci-scripts/main.py --mode=LogCollectMME --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type}"
echo '\u2705 \u001B[32mLog Transfer (MME)\u001B[0m'
sh "sshpass -p \'${EPC_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${EPC_Username}@${params.EPC_IPAddress}:${EPC_SourceCodePath}/scripts/mme.log.zip ./mme.log.${env.BUILD_ID}.zip || true"
}
script {
dir ('ci-scripts') {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password']
]) {
sh "python3 main.py --mode=LogCollectBuild --eNBIPAddress=${params.eNB_IPAddress} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath}"
sh "python3 main.py --mode=LogCollecteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath}"
sh "sshpass -p \'${eNB_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${eNB_Username}@${params.eNB_IPAddress}:${eNB_SourceCodePath}/cmake_targets/build.log.zip ./build.log.${env.BUILD_ID}.zip || true"
sh "sshpass -p \'${eNB_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${eNB_Username}@${params.eNB_IPAddress}:${eNB_SourceCodePath}/cmake_targets/enb.log.zip ./enb.log.${env.BUILD_ID}.zip || true"
// No need to remove since we are wiping out the folder on the eNB server during build
// sh "sshpass -p \'${eNB_Password}\' ssh -t -t -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${eNB_Username}@${params.eNB_IPAddress} 'cd ${eNB_SourceCodePath}; cd cmake_targets; if [ -e build.log.zip ]; then rm build.log.zip; fi;'"
// sh "sshpass -p \'${eNB_Password}\' ssh -t -t -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${eNB_Username}@${params.eNB_IPAddress} 'cd ${eNB_SourceCodePath}; cd cmake_targets; if [ -e enb.log.zip ]; then rm enb.log.zip; fi;'"
if(fileExists("build.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "build.log.${env.BUILD_ID}.zip"
// Same thing here, no need to remove.
// SCM folder is wiped out at build start on node
// sh "rm build.log.${env.BUILD_ID}.zip"
}
if(fileExists("enb.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "enb.log.${env.BUILD_ID}.zip"
// Same thing here, no need to remove.
// SCM folder is wiped out at build start on node
// sh "rm enb.log.${env.BUILD_ID}.zip"
}
}
if(fileExists("mme.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "mme.log.${env.BUILD_ID}.zip"
}
}
}
}
stage('Log Collection (EPC)') {
stage('Log Collection (HSS)') {
steps {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
echo '\u2705 \u001B[32mLog Collection (HSS)\u001B[0m'
sh "python3 ci-scripts/main.py --mode=LogCollectHSS --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type}"
echo '\u2705 \u001B[32mLog Transfer (HSS)\u001B[0m'
sh "sshpass -p \'${EPC_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${EPC_Username}@${params.EPC_IPAddress}:${EPC_SourceCodePath}/scripts/hss.log.zip ./hss.log.${env.BUILD_ID}.zip || true"
}
script {
dir ('ci-scripts') {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 main.py --mode=LogCollectSPGW --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type} "
sh "python3 main.py --mode=LogCollectMME --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type} "
sh "python3 main.py --mode=LogCollectHSS --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type} "
sh "python3 main.py --mode=LogCollectPing --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type} "
sh "sshpass -p \'${EPC_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${EPC_Username}@${params.EPC_IPAddress}:${EPC_SourceCodePath}/scripts/*.log.zip . || true"
if(fileExists("spgw.log.zip")) {
sh "mv spgw.log.zip ./spgw.log.${env.BUILD_ID}.zip"
archiveArtifacts "spgw.log.${env.BUILD_ID}.zip"
sh "rm spgw.log.${env.BUILD_ID}.zip"
}
if(fileExists("mme.log.zip")) {
sh "mv mme.log.zip ./mme.log.${env.BUILD_ID}.zip"
archiveArtifacts "mme.log.${env.BUILD_ID}.zip"
sh "rm mme.log.${env.BUILD_ID}.zip"
}
if(fileExists("hss.log.zip")) {
sh "mv hss.log.zip ./hss.log.${env.BUILD_ID}.zip"
archiveArtifacts "hss.log.${env.BUILD_ID}.zip"
sh "rm hss.log.${env.BUILD_ID}.zip"
}
if(fileExists("ping.log.zip")) {
sh "mv ping.log.zip ./ping.log.${env.BUILD_ID}.zip"
archiveArtifacts "ping.log.${env.BUILD_ID}.zip"
sh "rm ping.log.${env.BUILD_ID}.zip"
}
}
if(fileExists("hss.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "hss.log.${env.BUILD_ID}.zip"
}
}
}
}
stage('Log Collection (Ping)') {
steps {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
echo '\u2705 \u001B[32mLog Collection (Ping)\u001B[0m'
sh "python3 ci-scripts/main.py --mode=LogCollectPing --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --EPCType=${params.EPC_Type}"
echo '\u2705 \u001B[32mLog Transfer (Ping)\u001B[0m'
sh "sshpass -p \'${EPC_Password}\' scp -o 'StrictHostKeyChecking no' -o 'ConnectTimeout 10' ${EPC_Username}@${params.EPC_IPAddress}:${EPC_SourceCodePath}/scripts/ping.log.zip ./ping.log.${env.BUILD_ID}.zip || true"
}
script {
if(fileExists("ping.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "ping.log.${env.BUILD_ID}.zip"
}
}
}
......@@ -221,32 +393,55 @@ pipeline {
post {
always {
echo "Archiving Jenkins console log"
// Not working in Eurecom environment
/*
sh "wget --no-check-certificate --no-proxy ${env.JENKINS_URL}/job/${env.JOB_NAME}/${env.BUILD_ID}/consoleText -O consoleText.log || true"
sh "zip -m consoleText.log.${env.BUILD_ID}.zip consoleText.log || true"
script {
if(fileExists("consoleText.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "consoleText.log.${env.BUILD_ID}.zip"
sh "rm consoleText.log.${env.BUILD_ID}.zip"
if (params.pipelineZipsConsoleLog != null) {
if (params.pipelineZipsConsoleLog) {
echo "Archiving Jenkins console log"
sh "wget --no-check-certificate --no-proxy ${env.JENKINS_URL}/job/${env.JOB_NAME}/${env.BUILD_ID}/consoleText -O consoleText.log || true"
sh "zip -m consoleText.log.${env.BUILD_ID}.zip consoleText.log || true"
if(fileExists("consoleText.log.${env.BUILD_ID}.zip")) {
archiveArtifacts "consoleText.log.${env.BUILD_ID}.zip"
}
}
}
}
*/
}
// Making sure that we really shutdown every thing before leaving
failure {
script {
dir ('ci-scripts') {
try {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password'],
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.ADB_Credentials}", usernameVariable: 'ADB_Username', passwordVariable: 'ADB_Password']
]) {
sh "python3 main.py --mode=TesteNB --eNBIPAddress=${params.eNB_IPAddress} --eNBRepository=${GIT_URL} --eNBBranch=${GIT_BRANCH} --eNBCommitID=${GIT_COMMIT} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password} --eNBSourceCodePath=${params.eNB_SourceCodePath} --EPCIPAddress=${params.EPC_IPAddress} --EPCType=${params.EPC_Type} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCSourceCodePath=${params.EPC_SourceCodePath} --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password} --XMLTestFile=xml_files/terminate_epc.xml"
}
} catch (Exception e) {
echo "could not properly terminate everything"
if (!termStatusArray[termUE]) {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.ADB_Credentials}", usernameVariable: 'ADB_Username', passwordVariable: 'ADB_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateUE --ADBIPAddress=${params.ADB_IPAddress} --ADBUserName=${ADB_Username} --ADBPassword=${ADB_Password}"
}
}
if (!termStatusArray[termENB]) {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.eNB_Credentials}", usernameVariable: 'eNB_Username', passwordVariable: 'eNB_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateeNB --eNBIPAddress=${params.eNB_IPAddress} --eNBUserName=${eNB_Username} --eNBPassword=${eNB_Password}"
}
}
if (!termStatusArray[termSPGW]) {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateSPGW --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCType=${params.EPC_Type} --EPCSourceCodePath=${params.EPC_SourceCodePath}"
}
}
if (!termStatusArray[termMME]) {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateMME --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCType=${params.EPC_Type} --EPCSourceCodePath=${params.EPC_SourceCodePath}"
}
}
if (!termStatusArray[termHSS]) {
withCredentials([
[$class: 'UsernamePasswordMultiBinding', credentialsId: "${params.EPC_Credentials}", usernameVariable: 'EPC_Username', passwordVariable: 'EPC_Password']
]) {
sh "python3 ci-scripts/main.py --mode=TerminateHSS --EPCIPAddress=${params.EPC_IPAddress} --EPCUserName=${EPC_Username} --EPCPassword=${EPC_Password} --EPCType=${params.EPC_Type} --EPCSourceCodePath=${params.EPC_SourceCodePath}"
}
}
}
......
ci-scripts/conf_files/enb.band7.tm1.100PRB.usrpb210.conf 0 → 100644
View file @ a2a00d22
Active_eNBs = ( "eNB-Eurecom-LTEBox");
# Asn1_verbosity, choice in: none, info, annoying
Asn1_verbosity = "none";
eNBs =
(
{
////////// Identification parameters:
eNB_ID = 0xe00;
cell_type = "CELL_MACRO_ENB";
eNB_name = "eNB-Eurecom-LTEBox";
// Tracking area code, 0x0000 and 0xfffe are reserved values
tracking_area_code = "1";
mobile_country_code = "208";
mobile_network_code = "92";
tr_s_preference = "local_mac"
////////// Physical parameters:
component_carriers = (
{
node_function = "3GPP_eNODEB";
node_timing = "synch_to_ext_device";
node_synch_ref = 0;
frame_type = "FDD";
tdd_config = 3;
tdd_config_s = 0;
prefix_type = "NORMAL";
eutra_band = 7;
downlink_frequency = 2685000000L;
uplink_frequency_offset = -120000000;
Nid_cell = 0;
N_RB_DL = 100;
Nid_cell_mbsfn = 0;
nb_antenna_ports = 1;
nb_antennas_tx = 1;
nb_antennas_rx = 1;
tx_gain = 90;
rx_gain = 125;
pbch_repetition = "FALSE";
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
prach_zero_correlation = 1;
prach_freq_offset = 2;
pucch_delta_shift = 1;
pucch_nRB_CQI = 0;
pucch_nCS_AN = 0;
pucch_n1_AN = 0;
pdsch_referenceSignalPower = -29;
pdsch_p_b = 0;
pusch_n_SB = 1;
pusch_enable64QAM = "DISABLE";
pusch_hoppingMode = "interSubFrame";
pusch_hoppingOffset = 0;
pusch_groupHoppingEnabled = "ENABLE";
pusch_groupAssignment = 0;
pusch_sequenceHoppingEnabled = "DISABLE";
pusch_nDMRS1 = 1;
phich_duration = "NORMAL";
phich_resource = "ONESIXTH";
srs_enable = "DISABLE";
/* srs_BandwidthConfig =;
srs_SubframeConfig =;
srs_ackNackST =;
srs_MaxUpPts =;*/
pusch_p0_Nominal = -96;
pusch_alpha = "AL1";
pucch_p0_Nominal = -104;
msg3_delta_Preamble = 6;
pucch_deltaF_Format1 = "deltaF2";
pucch_deltaF_Format1b = "deltaF3";
pucch_deltaF_Format2 = "deltaF0";
pucch_deltaF_Format2a = "deltaF0";
pucch_deltaF_Format2b = "deltaF0";
rach_numberOfRA_Preambles = 64;
rach_preamblesGroupAConfig = "DISABLE";
/*
rach_sizeOfRA_PreamblesGroupA = ;
rach_messageSizeGroupA = ;
rach_messagePowerOffsetGroupB = ;
*/
rach_powerRampingStep = 4;
rach_preambleInitialReceivedTargetPower = -108;
rach_preambleTransMax = 10;
rach_raResponseWindowSize = 10;
rach_macContentionResolutionTimer = 48;
rach_maxHARQ_Msg3Tx = 4;
pcch_default_PagingCycle = 128;
pcch_nB = "oneT";
bcch_modificationPeriodCoeff = 2;
ue_TimersAndConstants_t300 = 1000;
ue_TimersAndConstants_t301 = 1000;
ue_TimersAndConstants_t310 = 1000;
ue_TimersAndConstants_t311 = 10000;
ue_TimersAndConstants_n310 = 20;
ue_TimersAndConstants_n311 = 1;
ue_TransmissionMode = 1;
//Parameters for SIB18
rxPool_sc_CP_Len = "normal";
rxPool_sc_Period = "sf40";
rxPool_data_CP_Len = "normal";
rxPool_ResourceConfig_prb_Num = 20;
rxPool_ResourceConfig_prb_Start = 5;
rxPool_ResourceConfig_prb_End = 44;
rxPool_ResourceConfig_offsetIndicator_present = "prSmall";
rxPool_ResourceConfig_offsetIndicator_choice = 0;
rxPool_ResourceConfig_subframeBitmap_present = "prBs40";
rxPool_ResourceConfig_subframeBitmap_choice_bs_buf = "00000000000000000000";
rxPool_ResourceConfig_subframeBitmap_choice_bs_size = 5;
rxPool_ResourceConfig_subframeBitmap_choice_bs_bits_unused = 0;
/* rxPool_dataHoppingConfig_hoppingParameter = 0;
rxPool_dataHoppingConfig_numSubbands = "ns1";
rxPool_dataHoppingConfig_rbOffset = 0;
rxPool_commTxResourceUC-ReqAllowed = "TRUE";
*/
// Parameters for SIB19
discRxPool_cp_Len = "normal"
discRxPool_discPeriod = "rf32"
discRxPool_numRetx = 1;
discRxPool_numRepetition = 2;
discRxPool_ResourceConfig_prb_Num = 5;
discRxPool_ResourceConfig_prb_Start = 3;
discRxPool_ResourceConfig_prb_End = 21;
discRxPool_ResourceConfig_offsetIndicator_present = "prSmall";
discRxPool_ResourceConfig_offsetIndicator_choice = 0;
discRxPool_ResourceConfig_subframeBitmap_present = "prBs40";
discRxPool_ResourceConfig_subframeBitmap_choice_bs_buf = "f0ffffffff";
discRxPool_ResourceConfig_subframeBitmap_choice_bs_size = 5;
discRxPool_ResourceConfig_subframeBitmap_choice_bs_bits_unused = 0;
}
);
srb1_parameters :
{
# timer_poll_retransmit = (ms) [5, 10, 15, 20,... 250, 300, 350, ... 500]
timer_poll_retransmit = 80;
# timer_reordering = (ms) [0,5, ... 100, 110, 120, ... ,200]
timer_reordering = 35;
# timer_reordering = (ms) [0,5, ... 250, 300, 350, ... ,500]
timer_status_prohibit = 0;
# poll_pdu = [4, 8, 16, 32 , 64, 128, 256, infinity(>10000)]
poll_pdu = 4;
# poll_byte = (kB) [25,50,75,100,125,250,375,500,750,1000,1250,1500,2000,3000,infinity(>10000)]
poll_byte = 99999;
# max_retx_threshold = [1, 2, 3, 4 , 6, 8, 16, 32]
max_retx_threshold = 4;
}
# ------- SCTP definitions
SCTP :
{
# Number of streams to use in input/output
SCTP_INSTREAMS = 2;
SCTP_OUTSTREAMS = 2;
};
////////// MME parameters:
mme_ip_address = ( { ipv4 = "192.168.12.26";
ipv6 = "192:168:30::17";
active = "yes";
preference = "ipv4";
}
);
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.111/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.111/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
}
);
MACRLCs = (
{
num_cc = 1;
tr_s_preference = "local_L1";
tr_n_preference = "local_RRC";
phy_test_mode = 0;
puSch10xSnr = 200;
puCch10xSnr = 200;
}
);
L1s = (
{
num_cc = 1;
tr_n_preference = "local_mac";
}
);
RUs = (
{
local_rf = "yes"
nb_tx = 1
nb_rx = 1
att_tx = 0
att_rx = 0;
bands = [7];
max_pdschReferenceSignalPower = -27;
max_rxgain = 125;
eNB_instances = [0];
}
);
NETWORK_CONTROLLER :
{
FLEXRAN_ENABLED = "no";
FLEXRAN_INTERFACE_NAME = "lo";
FLEXRAN_IPV4_ADDRESS = "127.0.0.1";
FLEXRAN_PORT = 2210;
FLEXRAN_CACHE = "/mnt/oai_agent_cache";
FLEXRAN_AWAIT_RECONF = "no";
};
log_config :
{
global_log_level ="info";
global_log_verbosity ="medium";
hw_log_level ="info";
hw_log_verbosity ="medium";
phy_log_level ="info";
phy_log_verbosity ="medium";
mac_log_level ="info";
mac_log_verbosity ="high";
rlc_log_level ="info";
rlc_log_verbosity ="medium";
pdcp_log_level ="info";
pdcp_log_verbosity ="medium";
rrc_log_level ="info";
rrc_log_verbosity ="medium";
};
ci-scripts/conf_files/enb.band7.tm1.25PRB.usrpb210.conf 0 → 100644
View file @ a2a00d22
Active_eNBs = ( "eNB-Eurecom-LTEBox");
# Asn1_verbosity, choice in: none, info, annoying
Asn1_verbosity = "none";
eNBs =
(
{
////////// Identification parameters:
eNB_ID = 0xe00;
cell_type = "CELL_MACRO_ENB";
eNB_name = "eNB-Eurecom-LTEBox";
// Tracking area code, 0x0000 and 0xfffe are reserved values
tracking_area_code = "1";
mobile_country_code = "208";
mobile_network_code = "92";
tr_s_preference = "local_mac"
////////// Physical parameters:
component_carriers = (
{
node_function = "3GPP_eNODEB";
node_timing = "synch_to_ext_device";
node_synch_ref = 0;
frame_type = "FDD";
tdd_config = 3;
tdd_config_s = 0;
prefix_type = "NORMAL";
eutra_band = 7;
downlink_frequency = 2685000000L;
uplink_frequency_offset = -120000000;
Nid_cell = 0;
N_RB_DL = 25;
Nid_cell_mbsfn = 0;
nb_antenna_ports = 1;
nb_antennas_tx = 1;
nb_antennas_rx = 1;
tx_gain = 90;
rx_gain = 125;
pbch_repetition = "FALSE";
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
prach_zero_correlation = 1;
prach_freq_offset = 2;
pucch_delta_shift = 1;
pucch_nRB_CQI = 0;
pucch_nCS_AN = 0;
pucch_n1_AN = 0;
pdsch_referenceSignalPower = -25;
pdsch_p_b = 0;
pusch_n_SB = 1;
pusch_enable64QAM = "DISABLE";
pusch_hoppingMode = "interSubFrame";
pusch_hoppingOffset = 0;
pusch_groupHoppingEnabled = "ENABLE";
pusch_groupAssignment = 0;
pusch_sequenceHoppingEnabled = "DISABLE";
pusch_nDMRS1 = 1;
phich_duration = "NORMAL";
phich_resource = "ONESIXTH";
srs_enable = "DISABLE";
/* srs_BandwidthConfig =;
srs_SubframeConfig =;
srs_ackNackST =;
srs_MaxUpPts =;*/
pusch_p0_Nominal = -96;
pusch_alpha = "AL1";
pucch_p0_Nominal = -104;
msg3_delta_Preamble = 6;
pucch_deltaF_Format1 = "deltaF2";
pucch_deltaF_Format1b = "deltaF3";
pucch_deltaF_Format2 = "deltaF0";
pucch_deltaF_Format2a = "deltaF0";
pucch_deltaF_Format2b = "deltaF0";
rach_numberOfRA_Preambles = 64;
rach_preamblesGroupAConfig = "DISABLE";
/*
rach_sizeOfRA_PreamblesGroupA = ;
rach_messageSizeGroupA = ;
rach_messagePowerOffsetGroupB = ;
*/
rach_powerRampingStep = 4;
rach_preambleInitialReceivedTargetPower = -108;
rach_preambleTransMax = 10;
rach_raResponseWindowSize = 10;
rach_macContentionResolutionTimer = 48;
rach_maxHARQ_Msg3Tx = 4;
pcch_default_PagingCycle = 128;
pcch_nB = "oneT";
bcch_modificationPeriodCoeff = 2;
ue_TimersAndConstants_t300 = 1000;
ue_TimersAndConstants_t301 = 1000;
ue_TimersAndConstants_t310 = 1000;
ue_TimersAndConstants_t311 = 10000;
ue_TimersAndConstants_n310 = 20;
ue_TimersAndConstants_n311 = 1;
ue_TransmissionMode = 1;
//Parameters for SIB18
rxPool_sc_CP_Len = "normal";
rxPool_sc_Period = "sf40";
rxPool_data_CP_Len = "normal";
rxPool_ResourceConfig_prb_Num = 20;
rxPool_ResourceConfig_prb_Start = 5;
rxPool_ResourceConfig_prb_End = 44;
rxPool_ResourceConfig_offsetIndicator_present = "prSmall";
rxPool_ResourceConfig_offsetIndicator_choice = 0;
rxPool_ResourceConfig_subframeBitmap_present = "prBs40";
rxPool_ResourceConfig_subframeBitmap_choice_bs_buf = "00000000000000000000";
rxPool_ResourceConfig_subframeBitmap_choice_bs_size = 5;
rxPool_ResourceConfig_subframeBitmap_choice_bs_bits_unused = 0;
/* rxPool_dataHoppingConfig_hoppingParameter = 0;
rxPool_dataHoppingConfig_numSubbands = "ns1";
rxPool_dataHoppingConfig_rbOffset = 0;
rxPool_commTxResourceUC-ReqAllowed = "TRUE";
*/
// Parameters for SIB19
discRxPool_cp_Len = "normal"
discRxPool_discPeriod = "rf32"
discRxPool_numRetx = 1;
discRxPool_numRepetition = 2;
discRxPool_ResourceConfig_prb_Num = 5;
discRxPool_ResourceConfig_prb_Start = 3;
discRxPool_ResourceConfig_prb_End = 21;
discRxPool_ResourceConfig_offsetIndicator_present = "prSmall";
discRxPool_ResourceConfig_offsetIndicator_choice = 0;
discRxPool_ResourceConfig_subframeBitmap_present = "prBs40";
discRxPool_ResourceConfig_subframeBitmap_choice_bs_buf = "f0ffffffff";
discRxPool_ResourceConfig_subframeBitmap_choice_bs_size = 5;
discRxPool_ResourceConfig_subframeBitmap_choice_bs_bits_unused = 0;
}
);
srb1_parameters :
{
# timer_poll_retransmit = (ms) [5, 10, 15, 20,... 250, 300, 350, ... 500]
timer_poll_retransmit = 80;
# timer_reordering = (ms) [0,5, ... 100, 110, 120, ... ,200]
timer_reordering = 35;
# timer_reordering = (ms) [0,5, ... 250, 300, 350, ... ,500]
timer_status_prohibit = 0;
# poll_pdu = [4, 8, 16, 32 , 64, 128, 256, infinity(>10000)]
poll_pdu = 4;
# poll_byte = (kB) [25,50,75,100,125,250,375,500,750,1000,1250,1500,2000,3000,infinity(>10000)]
poll_byte = 99999;
# max_retx_threshold = [1, 2, 3, 4 , 6, 8, 16, 32]
max_retx_threshold = 4;
}
# ------- SCTP definitions
SCTP :
{
# Number of streams to use in input/output
SCTP_INSTREAMS = 2;
SCTP_OUTSTREAMS = 2;
};
////////// MME parameters:
mme_ip_address = ( { ipv4 = "192.168.12.26";
ipv6 = "192:168:30::17";
active = "yes";
preference = "ipv4";
}
);
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.111/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.111/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
}
);
MACRLCs = (
{
num_cc = 1;
tr_s_preference = "local_L1";
tr_n_preference = "local_RRC";
phy_test_mode = 0;
puSch10xSnr = 200;
puCch10xSnr = 200;
}
);
L1s = (
{
num_cc = 1;
tr_n_preference = "local_mac";
}
);
RUs = (
{
local_rf = "yes"
nb_tx = 1
nb_rx = 1
att_tx = 0
att_rx = 0;
bands = [7];
max_pdschReferenceSignalPower = -27;
max_rxgain = 125;
eNB_instances = [0];
}
);
NETWORK_CONTROLLER :
{
FLEXRAN_ENABLED = "no";
FLEXRAN_INTERFACE_NAME = "lo";
FLEXRAN_IPV4_ADDRESS = "127.0.0.1";
FLEXRAN_PORT = 2210;
FLEXRAN_CACHE = "/mnt/oai_agent_cache";
FLEXRAN_AWAIT_RECONF = "no";
};
log_config :
{
global_log_level ="info";
global_log_verbosity ="medium";
hw_log_level ="info";
hw_log_verbosity ="medium";
phy_log_level ="info";
phy_log_verbosity ="medium";
mac_log_level ="info";
mac_log_verbosity ="high";
rlc_log_level ="info";
rlc_log_verbosity ="medium";
pdcp_log_level ="info";
pdcp_log_verbosity ="medium";
rrc_log_level ="info";
rrc_log_verbosity ="medium";
};
ci-scripts/conf_files/enb.band7.tm1.50PRB.usrpb210.conf 0 → 100644
View file @ a2a00d22
Active_eNBs = ( "eNB-Eurecom-LTEBox");
# Asn1_verbosity, choice in: none, info, annoying
Asn1_verbosity = "none";
eNBs =
(
{
////////// Identification parameters:
eNB_ID = 0xe00;
cell_type = "CELL_MACRO_ENB";
eNB_name = "eNB-Eurecom-LTEBox";
// Tracking area code, 0x0000 and 0xfffe are reserved values
tracking_area_code = "1";
mobile_country_code = "208";
mobile_network_code = "92";
tr_s_preference = "local_mac"
////////// Physical parameters:
component_carriers = (
{
node_function = "3GPP_eNODEB";
node_timing = "synch_to_ext_device";
node_synch_ref = 0;
frame_type = "FDD";
tdd_config = 3;
tdd_config_s = 0;
prefix_type = "NORMAL";
eutra_band = 7;
downlink_frequency = 2685000000L;
uplink_frequency_offset = -120000000;
Nid_cell = 0;
N_RB_DL = 50;
Nid_cell_mbsfn = 0;
nb_antenna_ports = 1;
nb_antennas_tx = 1;
nb_antennas_rx = 1;
tx_gain = 90;
rx_gain = 125;
pbch_repetition = "FALSE";
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
prach_zero_correlation = 1;
prach_freq_offset = 2;
pucch_delta_shift = 1;
pucch_nRB_CQI = 0;
pucch_nCS_AN = 0;
pucch_n1_AN = 0;
pdsch_referenceSignalPower = -27;
pdsch_p_b = 0;
pusch_n_SB = 1;
pusch_enable64QAM = "DISABLE";
pusch_hoppingMode = "interSubFrame";
pusch_hoppingOffset = 0;
pusch_groupHoppingEnabled = "ENABLE";
pusch_groupAssignment = 0;
pusch_sequenceHoppingEnabled = "DISABLE";
pusch_nDMRS1 = 1;
phich_duration = "NORMAL";
phich_resource = "ONESIXTH";
srs_enable = "DISABLE";
/* srs_BandwidthConfig =;
srs_SubframeConfig =;
srs_ackNackST =;
srs_MaxUpPts =;*/
pusch_p0_Nominal = -96;
pusch_alpha = "AL1";
pucch_p0_Nominal = -104;
msg3_delta_Preamble = 6;
pucch_deltaF_Format1 = "deltaF2";
pucch_deltaF_Format1b = "deltaF3";
pucch_deltaF_Format2 = "deltaF0";
pucch_deltaF_Format2a = "deltaF0";
pucch_deltaF_Format2b = "deltaF0";
rach_numberOfRA_Preambles = 64;
rach_preamblesGroupAConfig = "DISABLE";
/*
rach_sizeOfRA_PreamblesGroupA = ;
rach_messageSizeGroupA = ;
rach_messagePowerOffsetGroupB = ;
*/
rach_powerRampingStep = 4;
rach_preambleInitialReceivedTargetPower = -108;
rach_preambleTransMax = 10;
rach_raResponseWindowSize = 10;
rach_macContentionResolutionTimer = 48;
rach_maxHARQ_Msg3Tx = 4;
pcch_default_PagingCycle = 128;
pcch_nB = "oneT";
bcch_modificationPeriodCoeff = 2;
ue_TimersAndConstants_t300 = 1000;
ue_TimersAndConstants_t301 = 1000;
ue_TimersAndConstants_t310 = 1000;
ue_TimersAndConstants_t311 = 10000;
ue_TimersAndConstants_n310 = 20;
ue_TimersAndConstants_n311 = 1;
ue_TransmissionMode = 1;
//Parameters for SIB18
rxPool_sc_CP_Len = "normal";
rxPool_sc_Period = "sf40";
rxPool_data_CP_Len = "normal";
rxPool_ResourceConfig_prb_Num = 20;
rxPool_ResourceConfig_prb_Start = 5;
rxPool_ResourceConfig_prb_End = 44;
rxPool_ResourceConfig_offsetIndicator_present = "prSmall";
rxPool_ResourceConfig_offsetIndicator_choice = 0;
rxPool_ResourceConfig_subframeBitmap_present = "prBs40";
rxPool_ResourceConfig_subframeBitmap_choice_bs_buf = "00000000000000000000";
rxPool_ResourceConfig_subframeBitmap_choice_bs_size = 5;
rxPool_ResourceConfig_subframeBitmap_choice_bs_bits_unused = 0;
/* rxPool_dataHoppingConfig_hoppingParameter = 0;
rxPool_dataHoppingConfig_numSubbands = "ns1";
rxPool_dataHoppingConfig_rbOffset = 0;
rxPool_commTxResourceUC-ReqAllowed = "TRUE";
*/
// Parameters for SIB19
discRxPool_cp_Len = "normal"
discRxPool_discPeriod = "rf32"
discRxPool_numRetx = 1;
discRxPool_numRepetition = 2;
discRxPool_ResourceConfig_prb_Num = 5;
discRxPool_ResourceConfig_prb_Start = 3;
discRxPool_ResourceConfig_prb_End = 21;
discRxPool_ResourceConfig_offsetIndicator_present = "prSmall";
discRxPool_ResourceConfig_offsetIndicator_choice = 0;
discRxPool_ResourceConfig_subframeBitmap_present = "prBs40";
discRxPool_ResourceConfig_subframeBitmap_choice_bs_buf = "f0ffffffff";
discRxPool_ResourceConfig_subframeBitmap_choice_bs_size = 5;
discRxPool_ResourceConfig_subframeBitmap_choice_bs_bits_unused = 0;
}
);
srb1_parameters :
{
# timer_poll_retransmit = (ms) [5, 10, 15, 20,... 250, 300, 350, ... 500]
timer_poll_retransmit = 80;
# timer_reordering = (ms) [0,5, ... 100, 110, 120, ... ,200]
timer_reordering = 35;
# timer_reordering = (ms) [0,5, ... 250, 300, 350, ... ,500]
timer_status_prohibit = 0;
# poll_pdu = [4, 8, 16, 32 , 64, 128, 256, infinity(>10000)]
poll_pdu = 4;
# poll_byte = (kB) [25,50,75,100,125,250,375,500,750,1000,1250,1500,2000,3000,infinity(>10000)]
poll_byte = 99999;
# max_retx_threshold = [1, 2, 3, 4 , 6, 8, 16, 32]
max_retx_threshold = 4;
}
# ------- SCTP definitions
SCTP :
{
# Number of streams to use in input/output
SCTP_INSTREAMS = 2;
SCTP_OUTSTREAMS = 2;
};
////////// MME parameters:
mme_ip_address = ( { ipv4 = "192.168.12.26";
ipv6 = "192:168:30::17";
active = "yes";
preference = "ipv4";
}
);
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.111/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.111/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
}
);
MACRLCs = (
{
num_cc = 1;
tr_s_preference = "local_L1";
tr_n_preference = "local_RRC";
phy_test_mode = 0;
puSch10xSnr = 200;
puCch10xSnr = 200;
}
);
L1s = (
{
num_cc = 1;
tr_n_preference = "local_mac";
}
);
RUs = (
{
local_rf = "yes"
nb_tx = 1
nb_rx = 1
att_tx = 0
att_rx = 0;
bands = [7];
max_pdschReferenceSignalPower = -27;
max_rxgain = 125;
eNB_instances = [0];
}
);
NETWORK_CONTROLLER :
{
FLEXRAN_ENABLED = "no";
FLEXRAN_INTERFACE_NAME = "lo";
FLEXRAN_IPV4_ADDRESS = "127.0.0.1";
FLEXRAN_PORT = 2210;
FLEXRAN_CACHE = "/mnt/oai_agent_cache";
FLEXRAN_AWAIT_RECONF = "no";
};
log_config :
{
global_log_level ="info";
global_log_verbosity ="medium";
hw_log_level ="info";
hw_log_verbosity ="medium";
phy_log_level ="info";
phy_log_verbosity ="medium";
mac_log_level ="info";
mac_log_verbosity ="high";
rlc_log_level ="info";
rlc_log_verbosity ="medium";
pdcp_log_level ="info";
pdcp_log_verbosity ="medium";
rrc_log_level ="info";
rrc_log_verbosity ="medium";
};
ci-scripts/main.py
View file @ a2a00d22
......@@ -221,16 +221,39 @@ class SSHConnection():
self.CheckProcessExist(initialize_eNB_flag)
self.open(self.eNBIPAddress, self.eNBUserName, self.eNBPassword)
self.command('cd ' + self.eNBSourceCodePath, '\$', 5)
self.command('cd targets/PROJECTS/GENERIC-LTE-EPC/CONF/', '\$', 5)
self.command('cp ' + self.Initialize_eNB_args + ' ci-' + self.Initialize_eNB_args, '\$', 5)
self.command('sed -i -e \'s/mme_ip_address.*$/mme_ip_address = ( { ipv4 = "' + self.EPCIPAddress + '";/\' ci-' + self.Initialize_eNB_args, '\$', 2);
self.command('sed -i -e \'s/ENB_IPV4_ADDRESS_FOR_S1_MME.*$/ENB_IPV4_ADDRESS_FOR_S1_MME = "' + self.eNBIPAddress + '";/\' ci-' + self.Initialize_eNB_args, '\$', 2);
self.command('sed -i -e \'s/ENB_IPV4_ADDRESS_FOR_S1U.*$/ENB_IPV4_ADDRESS_FOR_S1U = "' + self.eNBIPAddress + '";/\' ci-' + self.Initialize_eNB_args, '\$', 2);
self.command('sed -i -e \'s/mobile_network_code = "93";/mobile_network_code = "92";/\' ci-' + self.Initialize_eNB_args, '\$', 2);
self.command('cd ' + self.eNBSourceCodePath, '\$', 5)
# Initialize_eNB_args usually start with -O and followed by the location in repository
full_config_file = self.Initialize_eNB_args.replace('-O ','')
config_path, config_file = os.path.split(full_config_file)
ci_full_config_file = config_path + '/ci-' + config_file
# Make a copy and adapt to EPC / eNB IP addresses
self.command('cp ' + full_config_file + ' ' + ci_full_config_file, '\$', 5)
self.command('sed -i -e \'s/mme_ip_address.*$/mme_ip_address = ( { ipv4 = "' + self.EPCIPAddress + '";/\' ' + ci_full_config_file, '\$', 2);
self.command('sed -i -e \'s/ENB_IPV4_ADDRESS_FOR_S1_MME.*$/ENB_IPV4_ADDRESS_FOR_S1_MME = "' + self.eNBIPAddress + '";/\' ' + ci_full_config_file, '\$', 2);
self.command('sed -i -e \'s/ENB_IPV4_ADDRESS_FOR_S1U.*$/ENB_IPV4_ADDRESS_FOR_S1U = "' + self.eNBIPAddress + '";/\' ' + ci_full_config_file, '\$', 2);
# Launch eNB with the modified config file
self.command('source oaienv', '\$', 5)
self.command('cd cmake_targets', '\$', 5)
self.command('echo ' + self.eNBPassword + ' | ' + 'sudo -S -E ./lte_build_oai/build/lte-softmodem -O ' + self.eNBSourceCodePath + '/targets/PROJECTS/GENERIC-LTE-EPC/CONF/ci-' + self.Initialize_eNB_args + ' 2>&1 | stdbuf -o0 tee -a enb_' + SSH.testCase_id + '.log &', 'got sync', 60)
# Replacing with a nohup and a direct redirection of stdout to a file
self.command('echo ' + self.eNBPassword + ' | nohup sudo -S -E ./lte_build_oai/build/lte-softmodem -O ' + self.eNBSourceCodePath + '/' + ci_full_config_file + ' > enb_' + SSH.testCase_id + '.log 2>&1 &', '\$', 5)
# Using a tail -f with result with an unexpected timeout message
#self.command('tail -f enb_' + SSH.testCase_id + '.log', 'got sync', 60)
time.sleep(6)
doLoop = True
loopCounter = 10
while (doLoop):
loopCounter = loopCounter - 1
if (loopCounter == 0):
doLoop = False
logging.debug('\u001B[1;37;41m Starting eNB Failed -- taking too much time \u001B[0m')
sys.exit(1)
self.command('stdbuf -o0 cat enb_' + SSH.testCase_id + '.log', '\$', 10)
result = re.search('got sync', str(self.ssh.before))
if result is None:
time.sleep(6)
else:
doLoop = False
logging.debug('\u001B[1m Initialize eNB Completed\u001B[0m')
self.close()
def InitializeUE_common(self, device_id):
......@@ -312,7 +335,7 @@ class SSHConnection():
def DetachUE_common(self, device_id):
try:
self.open(self.ADBIPAddress, self.ADBUserName, self.ADBPassword)
self.command('stdbuf -o0 adb -s ' + device_id + ' shell /data/local/tmp/on', '\$', 60)
self.command('stdbuf -o0 adb -s ' + device_id + ' shell /data/local/tmp/off', '\$', 60)
logging.debug('\u001B[1mUE (' + device_id + ') Detach Completed\u001B[0m')
self.close()
except:
......@@ -482,8 +505,23 @@ class SSHConnection():
def Iperf_common(self, lock, UE_IPAddress, device_id, ue_num):
try:
useIperf3 = False
self.open(self.ADBIPAddress, self.ADBUserName, self.ADBPassword)
self.command('stdbuf -o0 adb -s ' + device_id + ' shell /data/local/tmp/iperf3 -s &', '\$', 5)
# Checking if iperf / iperf3 are installed
self.command('adb -s ' + device_id + ' shell "ls /data/local/tmp"', '\$', 5)
result = re.search('iperf3', str(self.ssh.before))
if result is None:
result = re.search('iperf', str(self.ssh.before))
if result is None:
logging.debug('\u001B[1;37;41m Neither iperf nor iperf3 installed on UE! \u001B[0m')
sys.exit(1)
else:
useIperf3 = True
if (useIperf3):
self.command('stdbuf -o0 adb -s ' + device_id + ' shell /data/local/tmp/iperf3 -s &', '\$', 5)
else:
self.command('rm -f /tmp/iperf_server_' + SSH.testCase_id + '_' + device_id + '.log', '\$', 5)
self.command('echo $USER; nohup adb -s ' + device_id + ' shell "/data/local/tmp/iperf -u -s -i 1" > /tmp/iperf_server_' + SSH.testCase_id + '_' + device_id + '.log &', self.ADBUserName, 5)
time.sleep(0.5)
self.close()
......@@ -511,31 +549,61 @@ class SSHConnection():
if result is None:
logging.debug('\u001B[1;37;41m Calculate Iperf bandwidth Failed! \u001B[0m')
sys.exit(1)
self.command('stdbuf -o0 iperf3 -c ' + UE_IPAddress + ' ' + result + ' 2>&1 | stdbuf -o0 tee -a iperf_' + SSH.testCase_id + '_' + device_id + '.log', '\$', int(iperf_time)*5.0)
result = re.search('(?P<bitrate>[0-9\.]+ [KMG]bits\/sec) +(?:|[0-9\.]+ ms +\d+\/\d+ \((?P<packetloss>[0-9\.]+)%\)) +(?:|receiver)\\\\r\\\\n(?:|\[ *\d+\] Sent \d+ datagrams)\\\\r\\\\niperf Done\.', str(self.ssh.before))
if result is None:
result = re.search('(?P<error>iperf3: error - [a-zA-Z0-9 :]+)', str(self.ssh.before))
self.command('rm -f iperf_' + SSH.testCase_id + '_' + device_id + '.log', '\$', 5)
if (useIperf3):
self.command('stdbuf -o0 iperf3 -c ' + UE_IPAddress + ' ' + result + ' 2>&1 | stdbuf -o0 tee -a iperf_' + SSH.testCase_id + '_' + device_id + '.log', '\$', int(iperf_time)*5.0)
result = re.search('(?P<bitrate>[0-9\.]+ [KMG]bits\/sec) +(?:|[0-9\.]+ ms +\d+\/\d+ \((?P<packetloss>[0-9\.]+)%\)) +(?:|receiver)\\\\r\\\\n(?:|\[ *\d+\] Sent \d+ datagrams)\\\\r\\\\niperf Done\.', str(self.ssh.before))
if result is None:
result = re.search('(?P<error>iperf: error - [a-zA-Z0-9 :]+)', str(self.ssh.before))
if result is not None:
logging.debug('\u001B[1;37;41m ' + result.group('error') + ' \u001B[0m')
else:
logging.debug('\u001B[1;37;41m Bitrate and/or Packet Loss Not Found! \u001B[0m')
sys.exit(1)
bitrate = result.group('bitrate')
packetloss = result.group('packetloss')
lock.acquire()
logging.debug('\u001B[1;37;44m iperf result (' + UE_IPAddress + ') \u001B[0m')
logging.debug('\u001B[1;34m Bitrate : ' + bitrate + '\u001B[0m')
if packetloss is not None:
logging.debug('\u001B[1;34m Packet Loss : ' + packetloss + '%\u001B[0m')
if float(packetloss) > float(self.iperf_packetloss_threshold):
logging.debug('\u001B[1;37;41m Packet Loss too high \u001B[0m')
lock.release()
sys.exit(1)
lock.release()
else:
self.command('stdbuf -o0 iperf -c ' + UE_IPAddress + ' ' + result + ' 2>&1 | stdbuf -o0 tee -a iperf_' + SSH.testCase_id + '_' + device_id + '.log', '\$', int(iperf_time)*5.0)
result = re.search('Server Report:', str(self.ssh.before))
if result is None:
result = re.search('read failed: Connection refused', str(self.ssh.before))
if result is not None:
logging.debug('\u001B[1;37;41m Could not connect to iperf server! \u001B[0m')
else:
logging.debug('\u001B[1;37;41m Server Report and Connection refused Not Found! \u001B[0m')
sys.exit(1)
result = re.search('Server Report:\\\\r\\\\n(?:|\[ *\d+\].*) (?P<bitrate>[0-9\.]+ [KMG]bits\/sec) +(?:|[0-9\.]+ ms +\d+\/\d+ \((?P<packetloss>[0-9\.]+)%\))', str(self.ssh.before))
if result is not None:
logging.debug('\u001B[1;37;41m ' + result.group('error') + ' \u001B[0m')
else:
logging.debug('\u001B[1;37;41m Bitrate and/or Packet Loss Not Found! \u001B[0m')
sys.exit(1)
bitrate = result.group('bitrate')
packetloss = result.group('packetloss')
lock.acquire()
logging.debug('\u001B[1;37;44m iperf3 result (' + UE_IPAddress + ') \u001B[0m')
logging.debug('\u001B[1;34m Bitrate : ' + bitrate + '\u001B[0m')
if packetloss is not None:
logging.debug('\u001B[1;34m Packet Loss : ' + packetloss + '%\u001B[0m')
if float(packetloss) > float(self.iperf_packetloss_threshold):
logging.debug('\u001B[1;37;41m Packet Loss too high \u001B[0m')
bitrate = result.group('bitrate')
packetloss = result.group('packetloss')
lock.acquire()
logging.debug('\u001B[1;37;44m iperf result (' + UE_IPAddress + ') \u001B[0m')
if bitrate is not None:
logging.debug('\u001B[1;34m Bitrate : ' + bitrate + '\u001B[0m')
if packetloss is not None:
logging.debug('\u001B[1;34m Packet Loss : ' + packetloss + '%\u001B[0m')
if float(packetloss) > float(self.iperf_packetloss_threshold):
logging.debug('\u001B[1;37;41m Packet Loss too high \u001B[0m')
lock.release()
sys.exit(1)
lock.release()
sys.exit(1)
lock.release()
self.close()
self.open(self.ADBIPAddress, self.ADBUserName, self.ADBPassword)
self.command('stdbuf -o0 adb -s ' + device_id + ' shell ps | grep iperf3 | grep -v grep', '\$', 5)
self.command('stdbuf -o0 adb -s ' + device_id + ' shell ps | grep --color=never iperf | grep -v grep', '\$', 5)
result = re.search('shell +(?P<pid>\d+)', str(self.ssh.before))
if result is not None:
pid_iperf = result.group('pid')
......@@ -670,7 +738,7 @@ class SSHConnection():
self.command('rm -f ./kill_hss.sh', '\$', 5)
self.command('echo ' + self.EPCPassword + ' | sudo -S daemon --name=simulated_hss --stop', '\$', 5)
time.sleep(2)
self.command('ps -aux | egrep "hss_sim|simulated_hss" | grep -v grep | awk \'BEGIN{n=0}{pidId[n]=$2;n=n+1}END{print "kill -9 " pidId[0] " " pidId[1]}\' > ./kill_hss.sh', '\$', 5)
self.command('ps -aux | egrep --color=never "hss_sim|simulated_hss" | grep -v grep | awk \'BEGIN{n=0}{pidId[n]=$2;n=n+1}END{print "kill -9 " pidId[0] " " pidId[1]}\' > ./kill_hss.sh', '\$', 5)
self.command('chmod 755 ./kill_hss.sh', '\$', 5)
self.command('echo ' + self.EPCPassword + ' | sudo -S ./kill_hss.sh', '\$', 5)
self.command('rm ./kill_hss.sh', '\$', 5)
......@@ -710,17 +778,11 @@ class SSHConnection():
self.command('stdbuf -o0 adb -s ' + device_id + ' shell /data/local/tmp/off', '\$', 60)
logging.debug('\u001B[1mUE (' + device_id + ') Detach Completed\u001B[0m')
# to fix later
#self.command('stdbuf -o0 adb -s ' + device_id + ' shell ps | grep --color=never iperf3 | grep -v grep', '\$', 5)
#result = re.search('shell +(?P<pid>\d+)', str(self.ssh.before))
#if result is not None:
# pid_iperf = result.group('pid')
# self.command('stdbuf -o0 adb -s ' + device_id + ' shell kill -KILL ' + pid_iperf, '\$', 5)
#else:
# self.command('stdbuf -o0 ls', '\$', 5)
# if result is not None:
# pid_iperf = result.group('pid')
# self.command('stdbuf -o0 adb -s ' + device_id + ' shell kill -KILL ' + pid_iperf, '\$', 5)
self.command('stdbuf -o0 adb -s ' + device_id + ' shell ps | grep --color=never iperf | grep -v grep', '\$', 5)
result = re.search('shell +(?P<pid>\d+)', str(self.ssh.before))
if result is not None:
pid_iperf = result.group('pid')
self.command('stdbuf -o0 adb -s ' + device_id + ' shell kill -KILL ' + pid_iperf, '\$', 5)
self.close()
except:
os.kill(os.getppid(),signal.SIGUSR1)
......@@ -964,17 +1026,17 @@ elif re.match('^TerminateUE$', mode, re.IGNORECASE):
signal.signal(signal.SIGUSR1, receive_signal)
SSH.TerminateUE()
elif re.match('^TerminateHSS$', mode, re.IGNORECASE):
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '':
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCType == '' or SSH.EPCSourceCodePath == '':
Usage()
sys.exit('Insufficient Parameter')
SSH.TerminateHSS()
elif re.match('^TerminateMME$', mode, re.IGNORECASE):
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '':
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCType == '' or SSH.EPCSourceCodePath == '':
Usage()
sys.exit('Insufficient Parameter')
SSH.TerminateMME()
elif re.match('^TerminateSPGW$', mode, re.IGNORECASE):
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '':
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCType == '' or SSH.EPCSourceCodePath == '':
Usage()
sys.exit('Insufficient Parameter')
SSH.TerminateSPGW()
......@@ -989,17 +1051,17 @@ elif re.match('^LogCollecteNB$', mode, re.IGNORECASE):
sys.exit('Insufficient Parameter')
SSH.LogCollecteNB()
elif re.match('^LogCollectHSS$', mode, re.IGNORECASE):
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCSourceCodePath == '':
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCType == '' or SSH.EPCSourceCodePath == '':
Usage()
sys.exit('Insufficient Parameter')
SSH.LogCollectHSS()
elif re.match('^LogCollectMME$', mode, re.IGNORECASE):
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCSourceCodePath == '':
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCType == '' or SSH.EPCSourceCodePath == '':
Usage()
sys.exit('Insufficient Parameter')
SSH.LogCollectMME()
elif re.match('^LogCollectSPGW$', mode, re.IGNORECASE):
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCSourceCodePath == '':
if SSH.EPCIPAddress == '' or SSH.EPCUserName == '' or SSH.EPCPassword == '' or SSH.EPCType == '' or SSH.EPCSourceCodePath == '':
Usage()
sys.exit('Insufficient Parameter')
SSH.LogCollectSPGW()
......@@ -1062,7 +1124,7 @@ elif re.match('^TesteNB$', mode, re.IGNORECASE):
if (test_in_list(test, exclusion_tests)):
logging.debug('INFO: test will be skipped: ' + test)
else:
logging.debug('INFO: test will be run: ' + test)
#logging.debug('INFO: test will be run: ' + test)
todo_tests.append(test)
signal.signal(signal.SIGUSR1, receive_signal)
......
ci-scripts/xml_files/enb_usrp210_band7.xml 0 → 100644
View file @ a2a00d22
<testCaseList>
<TestCaseRequestedList>010101 050101 060101 070101 040101 030101 040301 040501 040601 040602 040603 040401 040201 030201 040101 030111 040301 040511 040611 040612 040613 040401 040201 030201</TestCaseRequestedList>
<TestCaseExclusionList></TestCaseExclusionList>
<testCase id="010101">
<class>Build_eNB</class>
<desc>Build eNB (USRP)</desc>
<Build_eNB_args>-w USRP -x -c --eNB</Build_eNB_args>
</testCase>
<testCase id="030101">
<class>Initialize_eNB</class>
<desc>Initialize eNB (FDD/Band7/5MHz)</desc>
<Initialize_eNB_args>-O ci-scripts/conf_files/enb.band7.tm1.25PRB.usrpb210.conf</Initialize_eNB_args>
</testCase>
<testCase id="030111">
<class>Initialize_eNB</class>
<desc>Initialize eNB (FDD/Band7/10MHz)</desc>
<Initialize_eNB_args>-O ci-scripts/conf_files/enb.band7.tm1.50PRB.usrpb210.conf</Initialize_eNB_args>
</testCase>
<testCase id="030201">
<class>Terminate_eNB</class>
<desc>Terminate eNB</desc>
</testCase>
<testCase id="040101">
<class>Initialize_UE</class>
<desc>Initialize UE</desc>
</testCase>
<testCase id="040201">
<class>Terminate_UE</class>
<desc>Terminate UE</desc>
</testCase>
<testCase id="040301">
<class>Attach_UE</class>
<desc>Attach UE</desc>
</testCase>
<testCase id="040401">
<class>Detach_UE</class>
<desc>Detach UE</desc>
</testCase>
<testCase id="040501">
<class>Ping</class>
<desc>ping (5MHz - 20 sec)</desc>
<ping_args>-c 20</ping_args>
<ping_packetloss_threshold>5</ping_packetloss_threshold>
</testCase>
<testCase id="040511">
<class>Ping</class>
<desc>ping (10MHz - 20 sec)</desc>
<ping_args>-c 20</ping_args>
<ping_packetloss_threshold>5</ping_packetloss_threshold>
</testCase>
<testCase id="040601">
<class>Iperf</class>
<desc>iperf (5MHz - DL/6Mbps/UDP)(60 sec)</desc>
<iperf_args>-u -b 6M -t 60 -i 1</iperf_args>
<iperf_packetloss_threshold>50</iperf_packetloss_threshold>
</testCase>
<testCase id="040602">
<class>Iperf</class>
<desc>iperf (5MHz - DL/13Mbps/UDP)(60 sec)</desc>
<iperf_args>-u -b 13M -t 60 -i 1</iperf_args>
<iperf_packetloss_threshold>50</iperf_packetloss_threshold>
</testCase>
<testCase id="040603">
<class>Iperf</class>
<desc>iperf (5MHz - DL/15Mbps/UDP)(60 sec)</desc>
<iperf_args>-u -b 15M -t 60 -i 1</iperf_args>
<iperf_packetloss_threshold>50</iperf_packetloss_threshold>
</testCase>
<testCase id="040611">
<class>Iperf</class>
<desc>iperf (10MHz - DL/6Mbps/UDP)(60 sec)</desc>
<iperf_args>-u -b 6M -t 60 -i 1</iperf_args>
<iperf_packetloss_threshold>50</iperf_packetloss_threshold>
</testCase>
<testCase id="040612">
<class>Iperf</class>
<desc>iperf (10MHz - DL/13Mbps/UDP)(60 sec)</desc>
<iperf_args>-u -b 13M -t 60 -i 1</iperf_args>
<iperf_packetloss_threshold>50</iperf_packetloss_threshold>
</testCase>
<testCase id="040613">
<class>Iperf</class>
<desc>iperf (10MHz - DL/15Mbps/UDP)(60 sec)</desc>
<iperf_args>-u -b 15M -t 60 -i 1</iperf_args>
<iperf_packetloss_threshold>50</iperf_packetloss_threshold>
</testCase>
<testCase id="050101">
<class>Initialize_HSS</class>
<desc>Initialize HSS</desc>
</testCase>
<testCase id="060101">
<class>Initialize_MME</class>
<desc>Initialize MME</desc>
</testCase>
<testCase id="070101">
<class>Initialize_SPGW</class>
<desc>Initialize SPGW</desc>
</testCase>
</testCaseList>
ci-scripts/xml_files/enb_usrpB210_band7_50PRB.xml
View file @ a2a00d22
......@@ -5,7 +5,7 @@
<testCase id="030101">
<class>Initialize_eNB</class>
<desc>Initialize eNB (FDD/Band1/5MHz/info)</desc>
<Initialize_eNB_args>enb.band7.tm1.50PRB.usrpb210.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O ci-scripts/conf_files/enb.band7.tm1.50PRB.usrpb210.conf</Initialize_eNB_args>
</testCase>
<testCase id="030201">
......
ci-scripts/xml_files/test_case_list_template.xml
View file @ a2a00d22
......@@ -19,37 +19,37 @@
<testCase id="030101">
<class>Initialize_eNB</class>
<desc>Initialize eNB (FDD/Band1/5MHz/info)</desc>
<Initialize_eNB_args>enb.band7.tm1.50PRB.usrpb210.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O enb.band7.tm1.50PRB.usrpb210.conf</Initialize_eNB_args>
</testCase>
<testCase id="030102">
<class>Initialize_eNB</class>
<desc>Initialize eNB (FDD/Band1/10MHz/info)</desc>
<Initialize_eNB_args>10M.band1.FDD.info.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O 10M.band1.FDD.info.conf</Initialize_eNB_args>
</testCase>
<testCase id="030103">
<class>Initialize_eNB</class>
<desc>Initialize eNB (FDD/Band1/20MHz/info)</desc>
<Initialize_eNB_args>20M.band1.FDD.info.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O 20M.band1.FDD.info.conf</Initialize_eNB_args>
</testCase>
<testCase id="030104">
<class>Initialize_eNB</class>
<desc>Initialize eNB (TDD/Band38/5MHz/info)</desc>
<Initialize_eNB_args>5M.band38.TDD.info.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O 5M.band38.TDD.info.conf</Initialize_eNB_args>
</testCase>
<testCase id="030105">
<class>Initialize_eNB</class>
<desc>Initialize eNB (TDD/Band38/10MHz/info)</desc>
<Initialize_eNB_args>10M.band38.TDD.info.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O 10M.band38.TDD.info.conf</Initialize_eNB_args>
</testCase>
<testCase id="030106">
<class>Initialize_eNB</class>
<desc>Initialize eNB (TDD/Band38/20MHz/info)</desc>
<Initialize_eNB_args>20M.band38.TDD.info.conf</Initialize_eNB_args>
<Initialize_eNB_args>-O 20M.band38.TDD.info.conf</Initialize_eNB_args>
</testCase>
<testCase id="030201">
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment