Merge remote-tracking branch 'origin/channel-simulation-in-rfsimulator' into fix-rfsim-sync-ue

cmake_targets/CMakeLists.txt

@@ -604,7 +604,6 @@ set(HWLIB_TCP_BRIDGE_OAI_SOURCE
 add_library(tcp_bridge_oai MODULE ${HWLIB_TCP_BRIDGE_OAI_SOURCE} )
 set_target_properties(tcp_bridge_oai PROPERTIES COMPILE_FLAGS "-fvisibility=hidden")
 
-
 ##########################################################
 
 include_directories ("${OPENAIR_TARGETS}/ARCH/COMMON")

targets/ARCH/COMMON/common_lib.c

@@ -80,12 +80,12 @@ int set_device(openair0_device *device) {
 int set_transport(openair0_device *device) {
   switch (device->transp_type) {
     case ETHERNET_TP:
-      printf("[%s] has loaded ETHERNET trasport protocol.\n",((device->host_type == RAU_HOST) ? "RAU": "RRU"));
+      LOG_I(HW,"[%s] has loaded ETHERNET trasport protocol.\n",((device->host_type == RAU_HOST) ? "RAU": "RRU"));
       return 0;
       break;
 
     case NONE_TP:
-      printf("[%s] has not loaded a transport protocol.\n",((device->host_type == RAU_HOST) ? "RAU": "RRU"));
+      LOG_I(HW,"[%s] has not loaded a transport protocol.\n",((device->host_type == RAU_HOST) ? "RAU": "RRU"));
       return 0;
       break;
 

targets/ARCH/rfsimulator/README.md

@@ -35,7 +35,6 @@ It should the set to "server" in the eNB or gNB
 ## 4G case
 For the UE, it should be set to the IP address of the eNB
 example: 
-
 ```bash
 sudo RFSIMULATOR=192.168.2.200 ./lte-uesoftmodem -C 2685000000 -r 50 
 ```
@@ -45,10 +44,7 @@ If you reach 'RA not active' on UE, be careful to generate a valid SIM
 ```bash
 $OPENAIR_DIR/targets/bin/conf2uedata -c $OPENAIR_DIR/openair3/NAS/TOOLS/ue_eurecom_test_sfr.conf -o .
 ```
-This simulator can also be used with the `--noS1` option, in this case you must run the eNodeB and the UE on different PCs. 
-
 ## 5G case
-
 After regular build, add the simulation driver
 (don't use ./build_oai -w SIMU until we merge 4G and 5G branches)
 ```bash

targets/ARCH/rfsimulator/simulator.c

@@ -3,6 +3,12 @@
   copyleft: OpenAirInterface Software Alliance and it's licence
 */
 
+/*
+ * Open issues and limitations
+ * The read and write should be called in the same thread, that is not new USRP UHD design
+ * When the opposite side switch from passive reading to active R+Write, the synchro is not fully deterministic
+ */
+
 #include <sys/socket.h>
 #include <netinet/in.h>
 #include <netinet/tcp.h>
@@ -129,6 +135,9 @@ void rxAddInput( struct complex16 *input_sig, struct complex16 *after_channel_si
     }
 
     out_ptr->r += round(rx_tmp.x*pathLossLinear + noise_per_sample*gaussdouble(0.0,1.0));
+    printf("in: %d, out %d= %f*%f + %f*%f\n",
+      input_sig[((TS+i)*nbTx)%CirSize].r, out_ptr->r , rx_tmp.x,
+      pathLossLinear, noise_per_sample,gaussdouble(0.0,1.0));
     out_ptr->i += round(rx_tmp.y*pathLossLinear + noise_per_sample*gaussdouble(0.0,1.0));
     out_ptr++;
   }
@@ -519,7 +528,7 @@ int rfsimulator_read(openair0_device *device, openair0_timestamp *ptimestamp, vo
   for (int a=0; a<nbAnt; a++)
     memset(samplesVoid[a],0,sampleToByte(nsamps,1));
 
-  // Add all input signal in the output buffer
+  // Add all input nodes signal in the output buffer
   for (int sock=0; sock<FD_SETSIZE; sock++) {
     buffer_t *ptr=&t->buf[sock];
 
@@ -578,7 +587,6 @@ __attribute__((__visibility__("default")))
 int device_init(openair0_device *device, openair0_config_t *openair0_cfg) {
   // to change the log level, use this on command line
   // --log_config.hw_log_level debug
-  //set_log(HW,OAILOG_DEBUG);
   rfsimulator_state_t *rfsimulator = (rfsimulator_state_t *)calloc(sizeof(rfsimulator_state_t),1);
 
   if ((rfsimulator->ip=getenv("RFSIMULATOR")) == NULL ) {

targets/RT/USER/lte-uesoftmodem.c

@@ -811,7 +811,7 @@ int main( int argc, char **argv ) {
   //p_exmimo_config->framing.tdd_config = TXRXSWITCH_TESTRX;
 
   if (IS_SOFTMODEM_SIML1 )  {
-    init_ocm((double)snr_dB,0);
+    init_ocm(snr_dB,0);
     PHY_vars_UE_g[0][0]->no_timing_correction = 1;
   }