build_helper 26.3 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
#/*
# * Licensed to the OpenAirInterface (OAI) Software Alliance under one or more
# * contributor license agreements.  See the NOTICE file distributed with
# * this work for additional information regarding copyright ownership.
# * The OpenAirInterface Software Alliance licenses this file to You under
# * the OAI Public License, Version 1.1  (the "License"); you may not use this file
# * except in compliance with the License.
# * You may obtain a copy of the License at
# *
# *      http://www.openairinterface.org/?page_id=698
# *
# * Unless required by applicable law or agreed to in writing, software
# * distributed under the License is distributed on an "AS IS" BASIS,
# * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# * See the License for the specific language governing permissions and
# * limitations under the License.
# *-------------------------------------------------------------------------------
# * For more information about the OpenAirInterface (OAI) Software Alliance:
# *      contact@openairinterface.org
# */

# file build_helper
# brief
# authors Laurent Thomas, Lionel GAUTHIER
#
#######################################
if [ ! -f /etc/os-release ]; then
  echo "No /etc/os-release file found. You're likely on an unsupported distro."
  exit -1
fi
OS_DISTRO=$(grep "^ID=" /etc/os-release | sed "s/ID=//" | sed "s/\"//g")
OS_RELEASE=$(grep "^VERSION_ID=" /etc/os-release | sed "s/VERSION_ID=//" | sed "s/\"//g")
case "$OS_DISTRO" in
  fedora) OS_BASEDISTRO="fedora"; INSTALLER="dnf"; CMAKE="cmake" ;;
35 36
  rhel)   OS_BASEDISTRO="fedora"; INSTALLER="yum --skip-broken"; CMAKE="cmake3" ;;
  centos) OS_BASEDISTRO="fedora"; INSTALLER="yum --skip-broken"; CMAKE="cmake3" ;;
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58
  debian) OS_BASEDISTRO="debian"; INSTALLER="apt-get"; CMAKE="cmake" ;;
  ubuntu) OS_BASEDISTRO="debian"; INSTALLER="apt-get"; CMAKE="cmake" ;;
esac
KERNEL_VERSION=$(uname -r | cut -d '.' -f1)
KERNEL_MAJOR=$(uname -r | cut -d '.' -f2)

SUDO='sudo -E'

###############################
## echo and  family
###############################
black='\E[30m'
red='\E[31m'
green='\E[32m'
yellow='\E[33m'
blue='\E[1;34m'
magenta='\E[35m'
cyan='\E[36m'
white='\E[37m'
reset_color='\E[00m'
COLORIZE=1

59
cecho()  {
60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97
    # Color-echo
    # arg1 = message
    # arg2 = color
    local default_msg="No Message."
    message=${1:-$default_msg}
    color=${2:-$green}
    [ "$COLORIZE" = "1" ] && message="$color$message$reset_color"
    echo -e "$message"
    return
}

echo_error()   { cecho "$*" $red          ;}
echo_fatal()   { cecho "$*" $red; exit -1 ;}
echo_warning() { cecho "$*" $yellow       ;}
echo_success() { cecho "$*" $green        ;}
echo_info()    { cecho "$*" $blue         ;}

########################
# distribution helpers #
########################

# This function return a string to identify the distribution we are running
# If we can't check the distribution, it returns "Unknown"
# This function return always true as exit code by design
# Examples:
#   ubuntu16.04
#   debian8.5
get_distribution_release() {
    if [[ ! -z "$OS_DISTRO$OS_RELEASE" ]]; then
        echo "$OS_DISTRO$OS_RELEASE"
    else
        echo Unknown
    fi
}

check_supported_distribution() {
    local distribution=$(get_distribution_release)
    case "$distribution" in
98
        "ubuntu18.04") return 0 ;;
99 100 101 102 103 104
        "ubuntu17.10") return 0 ;;
        "ubuntu17.04") return 0 ;;
        "ubuntu16.04") return 0 ;;
        "ubuntu14.04") return 0 ;;
        "fedora24")    return 0 ;;
        "rhel7")       return 0 ;;
cig's avatar
cig committed
105
        "rhel7.6")     return 0 ;;
106
        "rhel7.7")     return 0 ;;
107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151
        "centos7")     return 0 ;;
    esac
    return 1
}

##################
# Error handlers #
##################

handler_EXIT() {
	local exit_code=$?
    [ "$exit_code" -eq 0 ] || echo_error "build have failed"
	exit $exit_code
}

trap handler_EXIT EXIT

###########################
# Cleaners
###########################

clean_kernel() {
    $SUDO modprobe ip_tables
    $SUDO modprobe x_tables
    $SUDO iptables -P INPUT ACCEPT
    $SUDO iptables -F INPUT
    $SUDO iptables -P OUTPUT ACCEPT
    $SUDO iptables -F OUTPUT
    $SUDO iptables -P FORWARD ACCEPT
    $SUDO iptables -F FORWARD
    $SUDO iptables -t nat -F
    $SUDO iptables -t mangle -F
    $SUDO iptables -t filter -F
    $SUDO iptables -t raw -F
    echo_info "Flushed iptables"
    $SUDO rmmod nasmesh > /dev/null 2>&1
    $SUDO rmmod oai_nw_drv  > /dev/null 2>&1
    $SUDO rmmod openair_rf > /dev/null 2>&1
    $SUDO rmmod ue_ip > /dev/null 2>&1
    echo_info "removed drivers from kernel"
}

clean_all_files() {
 set_openair_env
 dir=$OPENAIR_DIR/cmake_targets
152
 rm -rf $dir/log $OPENAIR_DIR/targets/bin/*
153 154 155
 rm -rf $dir/ran_build $dir/ran_build_noLOG
 rm -rf $dir/lte-simulators/build 
 rm -rf $dir/phy_simulators/build $dir/nas_sim_tools/build 
156
 rm -rf $dir/oaisim_build_oai/build $dir/oaisim_build_oai/CMakeLists.txt
157
 rm -rf $dir/autotests/bin $dir/autotests/log $dir/autotests/*/build
158 159 160 161 162 163 164 165 166 167 168 169 170 171
}

###################################
# Compilers
###################################

#check_warnings:
#    print error message if the compilation had warnings
#argument:
#    $1: log file
check_warnings() {
  #we look for 'warning:' in the compilation log file
  #this is how gcc starts a warning
  #this is not perfect, we may get false positive
172
  warning_count=`grep "warning:" "$1" | egrep -v "jobserver unavailable|disabling jobserver mode" | wc -l`
173 174 175 176 177
  if [ $warning_count -gt 0 ]; then
    echo_error "WARNING: $warning_count warnings. See $1"
  fi
}

178 179 180 181 182 183 184 185 186 187 188 189
#check_errors:
#    print error message if the compilation had errors
#argument:
#    $1: log file
check_errors() {
  #we look for 'warning:' in the compilation log file
  error_count=`grep "error:" "$1" | wc -l`
  if [ $error_count -gt 0 ]; then
    echo_error "ERROR: $error_count error. See $1"
  fi
}

190 191
compilations() {
  cd $OPENAIR_DIR/cmake_targets/$1/build
192
  echo_info "Log file for compilation is being written to: $dlog/$2.$REL.txt"
193 194
  set +e
  {
195 196 197 198 199
    if [ "$BUILD_COVERITY_SCAN" == "1" ]; then
        COV_SCAN_PREFIX="cov-build --dir cov-int"
    else
        COV_SCAN_PREFIX=""
    fi
laurent's avatar
laurent committed
200 201 202
    if [ "$MAKE_CMD" != "" ]; then
       $MAKE_CMD $2
    else 
203
    if [ "$VERBOSE_COMPILE" == "1" ]; then
204
       $COV_SCAN_PREFIX make -j`nproc` $2 VERBOSE=$VERBOSE_COMPILE
205
    else
206
       $COV_SCAN_PREFIX make -j`nproc` $2
207
    fi
laurent's avatar
laurent committed
208
    fi
209
    ret=$?
210 211
  } > $dlog/$2.$REL.txt 2>&1
  set -e
212 213 214 215 216 217
  if [[ $ret -ne 0 ]]; then
     check_warnings "$dlog/$2.$REL.txt"
     check_errors "$dlog/$2.$REL.txt"
     echo_error "$2 compilation failed"
     exit 1
  fi
218 219 220 221 222
  if [ -s $3 ] ; then
     cp $3 $4
     echo_success "$2 compiled"
     check_warnings "$dlog/$2.$REL.txt"
  else
223 224
     check_warnings "$dlog/$2.$REL.txt"
     check_errors "$dlog/$2.$REL.txt"
225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244
     echo_error "$2 compilation failed"
     exit 1
  fi
}

############################################
# External packages installers
############################################

install_protobuf_from_source(){
    protobuf_install_log=$OPENAIR_DIR/cmake_targets/log/protobuf_install_log.txt
    echo_info "\nInstalling Google Protobuf from sources. The log file for Protobuf installation is here: $protobuf_install_log "
    (
    cd /tmp
    echo "Downloading protobuf"
    #rm -rf /tmp/protobuf-2.6.1.tar.gz* /tmp/protobuf-2.6.1
    #wget https://github.com/google/protobuf/releases/download/v2.6.1/protobuf-2.6.1.tar.gz
    #tar -xzvf protobuf-2.6.1.tar.gz --owner $USER --group $USER --no-same-owner
    #cd protobuf-2.6.1/
    rm -rf /tmp/protobuf-cpp-3.3.0.tar.gz* /tmp/protobuf-3.3.0
245
    wget --tries=3 --retry-connrefused https://github.com/google/protobuf/releases/download/v3.3.0/protobuf-cpp-3.3.0.tar.gz
246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286
    tar -xzvf protobuf-cpp-3.3.0.tar.gz --owner $USER --group $(groups | cut -d" " -f1) --no-same-owner
    cd protobuf-3.3.0/
    ./configure
    echo "Compiling protobuf"
    make -j`nproc`
    $SUDO make install
    $SUDO ldconfig
    ) >& $protobuf_install_log
}

install_protobuf_c_from_source(){
    protobuf_c_install_log=$OPENAIR_DIR/cmake_targets/log/protobuf_c_install_log.txt
    echo_info "\nInstalling Google Protobuf_C from sources. The log file for Protobuf_C installation is here: $protobuf_c_install_log "
    (
    if [[ "$OS_DISTRO" == "rhel" ]] || [[ "$OS_DISTRO" == "centos" ]]; then
        export PKG_CONFIG_PATH=/usr/local/lib/pkgconfig
    fi
    cd /tmp
    echo "Downloading protobuf-c"
    rm -rf /tmp/protobuf-c
    git clone https://github.com/protobuf-c/protobuf-c.git
    cd protobuf-c
	git checkout 2a46af42784abf86804d536f6e0122d47cfeea45
    ./autogen.sh
    ./configure
    echo "Compiling protobuf-c"
    make -j`nproc`
    $SUDO make install
    $SUDO ldconfig
    ) >& $protobuf_c_install_log
}

install_usrp_uhd_driver_from_source(){
    uhd_install_log=$OPENAIR_DIR/cmake_targets/log/uhd_install_log.txt
    echo_info "\nInstalling UHD driver from sources. The log file for UHD driver installation is here: $uhd_install_log "
    (
    cd /tmp
    echo "Downloading UHD driver"
    rm -rf /tmp/uhd
    git clone https://github.com/EttusResearch/uhd.git
    cd uhd
287
    git checkout tags/v3.13.0.2
288 289 290 291 292 293 294 295 296 297 298 299 300 301 302
    mkdir -p host/build
    cd host/build
    $CMAKE ../
    echo "Compiling UHD"
    make -j`nproc`
    make test
    $SUDO make install
    $SUDO ldconfig
    ) >& $uhd_install_log
}

check_install_usrp_uhd_driver(){
    if [[ "$OS_DISTRO" == "ubuntu" ]]; then
        #first we remove old installation
        $SUDO apt-get remove -y uhd || true
303
        $SUDO apt-get remove libuhd-dev libuhd003 uhd-host -y || true
304 305
        v=$(lsb_release -cs)
        $SUDO apt-add-repository --remove "deb http://files.ettus.com/binaries/uhd/repo/uhd/ubuntu/$v $v main"
306
        # The new USRP repository
307
        # Raphael Defosseux: Adding a loop on adding PPA because in CI the gpg key retrieve may
308 309 310 311 312 313 314 315 316 317 318 319 320 321 322
        # timeout due to proxy / network latencies in Eurecom on VM
        echo_info "\nAdding PPA repository ettusresearch/uhd\n"
        x=0
        while [ $x -le 5 ]
        do
            if $SUDO add-apt-repository ppa:ettusresearch/uhd -y
            then
                echo_info "add-apt-repository successful\n"
                break
            else
                echo_info "add-apt-repository failed, retrying...\n"
                sleep 30
            fi
            x=$((x + 1))
        done
323
        $SUDO apt-get update
324 325
        $SUDO apt-get -y install  python python-tk libboost-all-dev libusb-1.0-0-dev
        $SUDO apt-get -y install libuhd-dev libuhd003 uhd-host
326 327
    elif [[ "$OS_BASEDISTRO" == "fedora" ]]; then
        $SUDO $INSTALLER -y install python boost libusb-devel libusbx-devel boost-devel python-mako python-docutils cmake
328
        $SUDO -H pip install requests
329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344
        if [[ "$OS_DISTRO" == "rhel" ]] || [[ "$OS_DISTRO" == "centos" ]]; then
            # until EPEL repo hasn't bumped UHD driver to >=3.10 in EPEL, build driver from source
            $SUDO $INSTALLER -y remove uhd uhd-devel uhd-firmware
            install_usrp_uhd_driver_from_source
        else
            $SUDO $INSTALLER -y install uhd uhd-devel uhd-firmware
        fi
    fi
}

install_usrp_uhd_driver() {
    if [[ "$OS_DISTRO" == "ubuntu" ]]; then
        # We move uhd-host apart because it depends on linux kernel version
        # On newer kernels, it fails to install
        $SUDO apt-get -y install uhd-host
    fi
345 346
    # quick workaround for RHE7.6
    local distribution=$(get_distribution_release)
347
    if [ -z $1 ]; then
348
      if [[ "$OS_DISTRO" == "rhel" ]]; then
349 350 351 352
          $SUDO /usr/local/bin/uhd_images_downloader
      else
          $SUDO uhd_images_downloader
      fi
353
    else
354
      if [[ "$OS_DISTRO" == "rhel" ]]; then
355 356 357 358
          $SUDO /usr/local/bin/uhd_images_downloader -i $1
      else
          $SUDO uhd_images_downloader -i $1
      fi
359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380
    fi
}

install_bladerf_driver_from_source(){
    bladerf_install_log=$OPENAIR_DIR/cmake_targets/log/bladerf_install_log.txt
    echo_info "\nInstalling BladeRF driver from sources. The log file for BladeRF driver installation is here: $bladerf_install_log "
    (
    cd /tmp
    echo "Downloading BladeRF driver"
    rm -rf /tmp/bladeRF
    git clone https://github.com/Nuand/bladeRF.git
    cd bladeRF
    git checkout tags/2016.06
    mkdir -p build
    cd build
    $CMAKE ../
    echo "Compiling BladeRF driver"
    make
    $SUDO make install
    $SUDO ldconfig
    echo "Downloading FPGA and firmware images"
    cd /tmp/bladeRF
381 382
    wget --tries=3 --retry-connrefused https://www.nuand.com/fx3/bladeRF_fw_latest.img
    wget --tries=3 --retry-connrefused https://www.nuand.com/fpga/hostedx40-latest.rbf
383 384 385 386 387 388 389 390 391 392 393 394
    sudo mkdir -p /usr/share/Nuand/bladeRF
    sudo mv bladeRF_fw_latest.img /usr/share/Nuand/bladeRF/bladeRF_fw.img
    sudo mv hostedx40-latest.rbf /usr/share/Nuand/bladeRF/hostedx40.rbf
    ) >& $bladerf_install_log
}

check_install_bladerf_driver(){
    if [[ "$OS_DISTRO" == "ubuntu" ]]; then
        if [ "$(get_distribution_release)" == "ubuntu14.04" ] ; then
            $SUDO add-apt-repository -y ppa:bladerf/bladerf
            $SUDO apt-get update
        fi
395 396 397
        $SUDO apt-get install -y  bladerf libbladerf-dev
        $SUDO apt-get install -y bladerf-firmware-fx3
        $SUDO apt-get install -y bladerf-fpga-hostedx40
398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416
   elif [[ "$OS_BASEDISTRO" == "fedora" ]]; then
        install_bladerf_driver_from_source
   else
        echo_error "BladeRF Installer for OAI does not support automatic build. Install BladeRF compiling sources manually from BladeRF website"
   fi
}

flash_firmware_bladerf() {
	$SUDO bladeRF-cli --flash-firmware /usr/share/Nuand/bladeRF/bladeRF_fw.img
}

check_install_lmssdr_driver(){
	if ( [ -d "/usr/local/include/lime" ] &&
             [ -f "/usr/local/include/lime/LimeSuite.h" ] )
	then
  		echo_success "Found lmssdr drivers and tools installed from source"
        else
                echo_error "lmssdr support implies installing lmssdr drivers and tools" \
                           " from sources. check:"
Laurent's avatar
Laurent committed
417
                echo_info "https://wiki.myriadrf.org/Lime_Suite"
418
                echo_fatal "Cannot compile lmssdr device"
419 420 421 422 423
	fi


}

424 425 426 427 428 429 430
install_soapy_from_source(){
    soapy_install_log=$OPENAIR_DIR/cmake_targets/log/soapy_install_log.txt
    echo_info "\nInstalling Soapy EcoSystem from source. The log file for Soapy installation is here: $soapy_install_log "
    (
    cd /tmp
    echo "Downloading SoapySDR"
    rm -rf /tmp/soapysdr
Rahman Doost's avatar
Rahman Doost committed
431 432
    git clone -b soapy-sdr-0.7.0 --single-branch https://github.com/pothosware/SoapySDR.git
    cd SoapySDR
433 434 435 436 437 438 439 440 441 442 443
    #git checkout tags/release_003_010_001_001
    mkdir -p build
    cd build
    $CMAKE ../
    echo "Compiling SoapySDR"
    make -j`nproc`
    $SUDO make install
    $SUDO ldconfig
    cd /tmp
    echo "Downloading SoapyRemote"
    rm -rf /tmp/soapyremote
Rahman Doost's avatar
Rahman Doost committed
444 445
    git clone -b soapy-remote-0.5.0 --single-branch https://github.com/pothosware/SoapyRemote.git
    cd SoapyRemote
446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463
    #git checkout tags/release_003_010_001_001
    mkdir -p build
    cd build
    cmake ../
    echo "Compiling SoapyRemote"
    make -j`nproc`
    $SUDO make install
    $SUDO ldconfig
    ) >& $soapy_install_log
}

install_soapy_iris_from_source(){
    iris_install_log=$OPENAIR_DIR/cmake_targets/log/iris_install_log.txt
    echo_info "\nInstalling Iris driver from source. The log file for Iris driver installation is here: $iris_install_log "
    (
    cd /tmp
    echo "Downloading SoapyIris"
    rm -rf /tmp/sklk-soapyiris
Rahman Doost's avatar
Rahman Doost committed
464
    git clone -b soapy-iris-2018.08.0.1 --single-branch https://github.com/skylarkwireless/sklk-soapyiris.git
465 466 467 468 469 470 471 472 473 474 475 476 477 478
    cd sklk-soapyiris
    mkdir -p build
    cd build
    cmake ../
    echo "Compiling SoapyIris"
    make -j`nproc`
    $SUDO make install
    $SUDO ldconfig
    ) >& $iris_install_log
}

check_install_soapy () {
    #if [[ "$OS_DISTRO" == "ubuntu" ]]; then
        #first we remove old installation
Rahman Doost's avatar
Rahman Doost committed
479 480 481 482
    $SUDO apt-get remove -y soapysdr soapysdr-server libsoapysdr-dev python-soapysdr python3-soapysdr soapysdr-module-remote || true
        #$SUDO add-apt-repository -y ppa:myriadrf/drivers
        #$SUDO apt-get update
        #$SUDO apt-get install -y soapysdr soapysdr-server libsoapysdr-dev python-soapysdr python3-soapysdr soapysdr-module-remote
483 484 485

    #elif [[ "$OS_BASEDISTRO" == "fedora" ]]; then
    #    $SUDO $INSTALLER -y install software-properties-common python3-software-properties python-software-properties subversion git python3 python-numpy python3-numpy cmake swig python-dev
Rahman Doost's avatar
Rahman Doost committed
486
    install_soapy_from_source
487 488 489 490 491
    #fi
    install_soapy_iris_from_source

}

492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582
check_install_additional_tools (){
  $SUDO $INSTALLER update -y
  if [[ "$OS_DISTRO" == "ubuntu" ]]; then
    PACKAGE_LIST="\
	check \
	dialog \
	dkms \
	gawk \
	libboost-all-dev \
	libpthread-stubs0-dev \
	openvpn \
	pkg-config \
	python-dev  \
	python-pexpect \
	sshfs \
	swig  \
	tshark \
	uml-utilities \
	unzip  \
	valgrind  \
	vlan	  \
	ctags \
        ntpdate \
        iperf3 \
        android-tools-adb \
	wvdial \
        python-numpy \
        sshpass \
        nscd \
        bc \
        ntp \
        python-scipy \
        python-matplotlib"
  elif [[ "$OS_DISTRO" == "rhel" ]] || [[ "$OS_DISTRO" == "centos" ]]; then
    PACKAGE_LIST="\
      check \
      dialog \
      dkms \
      gawk \
      boost-devel \
      openvpn \
      pkgconfig \
      pexpect \
      sshfs \
      swig  \
      wireshark \
      unzip  \
      valgrind  \
      vconfig	  \
      ctags \
      ntpdate \
      iperf3 \
      wvdial \
      numpy \
      sshpass \
      nscd \
      python2-paramiko \
      python-pyroute2 \
      python-netifaces \
      scipy \
      python-matplotlib"
  elif [[ "$OS_DISTRO" == "fedora" ]]; then
    PACKAGE_LIST=" \
      check \
      dialog \
      dkms \
      gawk \
      boost-devel \
      openvpn \
      pkgconfig \
      python-pexpect \
      sshfs \
      swig  \
      wireshark \
      unzip  \
      valgrind  \
      vconfig	  \
      ctags \
      ntpdate \
      iperf3 \
      wvdial \
      python-numpy \
      sshpass \
      nscd \
      python2-paramiko \
      python-pyroute2 \
      python-netifaces \
      python2-scipy \
      python2-matplotlib"
  fi
    $SUDO $INSTALLER install -y $PACKAGE_LIST
583

584 585 586 587 588
    $SUDO rm -fr /opt/ssh
    $SUDO GIT_SSL_NO_VERIFY=true git clone https://gitlab.eurecom.fr/oai/ssh.git /opt/ssh

  #The packages below are already installed for Redhat distros (RHEL, CentOS, Fedora)
  if [[ "$OS_DISTRO" == "ubuntu" ]]; then
589 590
    $SUDO -H pip install paramiko
    $SUDO -H pip install pyroute2 colorama
591 592 593 594
    log_netiface=$OPENAIR_DIR/cmake_targets/log/netiface_install_log.txt
    echo_info "Installing Netinterfaces package. The logfile for installation is in $log_netiface"
    (
    $SUDO rm -fr /tmp/netifaces-0.10.4.tar.gz /tmp/netifaces
595
    wget --tries=3 --retry-connrefused -P /tmp  https://pypi.python.org/packages/18/fa/dd13d4910aea339c0bb87d2b3838d8fd923c11869b1f6e741dbd0ff3bc00/netifaces-0.10.4.tar.gz
596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616
    tar -xzvf /tmp/netifaces-0.10.4.tar.gz -C /tmp
    cd /tmp/netifaces-0.10.4
    $SUDO python setup.py install
    cd -
    ) >& $log_netiface
  fi
}

check_install_oai_software() {
    local specific_packages=""
    if ! check_supported_distribution; then
        echo_error "Your distribution $(get_distribution_release) is not supported by oai !"
        exit 1
    fi
    $SUDO $INSTALLER update -y
  if [[ "$OS_DISTRO" == "ubuntu" ]]; then
    local LAPACK_LIBNAME="liblapack.so"
    local LAPACK_TARGET="/usr/lib/atlas-base/atlas/liblapack.so"
    $SUDO apt install -y software-properties-common
    case "$(get_distribution_release)" in
        "ubuntu14.04")
Cedric Roux's avatar
Cedric Roux committed
617
            specific_packages="libtasn1-3-dev libgnutls-dev libatlas-dev iproute libconfig8-dev"
618 619 620 621 622
            # For iperf3
            $SUDO add-apt-repository "deb http://archive.ubuntu.com/ubuntu trusty-backports universe"
            $SUDO apt-get update
            ;;
        "ubuntu16.04")
Cedric Roux's avatar
Cedric Roux committed
623
            specific_packages="libtasn1-6-dev libgnutls-dev libatlas-dev iproute libconfig8-dev"
624 625
            ;;
        "ubuntu17.04")
Cedric Roux's avatar
Cedric Roux committed
626
            specific_packages="libtasn1-6-dev libgnutls28-dev libatlas-dev iproute libconfig8-dev"
627 628
            ;;
        "ubuntu17.10")
Cedric Roux's avatar
Cedric Roux committed
629
            specific_packages="libtasn1-6-dev libgnutls28-dev iproute libconfig8-dev"
630 631 632 633
            LAPACK_LIBNAME="liblapack.so-x86_64-linux-gnu"
            LAPACK_TARGET="/usr/lib/x86_64-linux-gnu/atlas/liblapack.so"
            ;;
        "ubuntu18.04")
Cedric Roux's avatar
Cedric Roux committed
634
            specific_packages="libtasn1-6-dev libgnutls28-dev iproute2 libconfig-dev"
635 636 637 638 639 640 641 642 643 644 645 646
            LAPACK_LIBNAME="liblapack.so-x86_64-linux-gnu"
            LAPACK_TARGET="/usr/lib/x86_64-linux-gnu/atlas/liblapack.so"
            ;;
    esac
    $SUDO apt-get install -y \
    $specific_packages \
	autoconf  \
	automake  \
	bison  \
	build-essential \
	cmake \
	cmake-curses-gui  \
laurent's avatar
laurent committed
647
        ninja-build \
648 649 650 651 652 653 654 655 656 657 658 659 660 661 662
	doxygen \
	doxygen-gui \
	texlive-latex-base \
	ethtool \
	flex  \
	gdb  \
	git \
	graphviz \
	gtkwave \
	guile-2.0-dev  \
	iperf \
	iptables \
	iptables-dev \
	libatlas-base-dev \
	libblas-dev \
663 664
  liblapack-dev\
  liblapacke-dev\
665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694
	libffi-dev \
	libforms-bin \
	libforms-dev \
	libgcrypt11-dev \
	libgmp-dev \
	libgtk-3-dev \
	libidn2-0-dev  \
	libidn11-dev \
	libmysqlclient-dev  \
	libpython2.7-dev \
	libsctp1  \
	libsctp-dev  \
	libssl-dev  \
	libtool  \
	libusb-1.0-0-dev \
	libxml2 \
	libxml2-dev  \
	libxslt1-dev \
	mscgen  \
	octave-signal \
	openssh-client \
	openssh-server \
	openssl \
	python  \
	subversion \
	xmlstarlet \
	python-pip \
	pydb \
	libyaml-dev \
	wget \
695 696
	libxpm-dev \
        libboost-all-dev
697 698 699 700 701 702 703 704 705 706 707 708

    $SUDO update-alternatives --set "$LAPACK_LIBNAME" "$LAPACK_TARGET"

    $SUDO apt-get install -y nettle-dev nettle-bin
  elif [[ "$OS_BASEDISTRO" == "fedora" ]]; then
    if [[ "$OS_DISTRO" == "rhel" ]] || [[ "$OS_DISTRO" == "centos" ]]; then
      if rpm -q epel-release > /dev/null; then
        echo "EPEL repos already present. Good."
      else
        echo "EPEL repos not present. Installing them."
        $SUDO $INSTALLER install -y https://dl.fedoraproject.org/pub/epel/epel-release-latest-7.noarch.rpm
      fi
Cedric Roux's avatar
Cedric Roux committed
709
      $SUDO $INSTALLER install -y python-epdb vim-common
710 711 712
    else
      $SUDO $INSTALLER install -y mscgen pydb
    fi
713

714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774
    $SUDO $INSTALLER install -y \
      autoconf \
      automake \
      bc \
      bison \
      $CMAKE \
      doxygen \
      ethtool \
      flex \
      gdb \
      git \
      graphviz \
      gtkwave \
      guile-devel \
      iperf \
      iproute \
      iptables \
      iptables-devel \
      atlas-devel \
      blas-devel \
      libconfig-devel \
      libffi-devel \
      xforms \
      xforms-devel \
      libgcrypt-devel \
      gmp-devel \
      gtk3-devel \
      libidn2-devel  \
      libidn-devel \
      mariadb-devel \
      lksctp-tools \
      lksctp-tools-devel \
      openssl-devel \
      libtasn1 \
      libtool \
      libusb-devel \
      libxml2 \
      libxml2-devel \
      libxslt-devel \
      openssh-clients \
      openssh-server \
      openssl \
      patch \
      psmisc \
      python \
      subversion \
      xmlstarlet \
      python-pip \
      wget \
      kernel-headers \
      kernel-devel \
      nettle-devel \
      gnutls-devel \
      libXpm-devel \
      lapack \
      lapack-devel \
      blas \
      blas-devel \
      libyaml-devel
  fi

775
    install_asn1c_from_source $1
776 777 778 779 780 781 782 783 784
    $SUDO rm -fr /opt/ssh
    $SUDO git clone https://gist.github.com/2190472.git /opt/ssh
}

install_asn1c_from_source(){
    asn1_install_log=$OPENAIR_DIR/cmake_targets/log/asn1c_install_log.txt
    echo_info "\nInstalling ASN1. The log file for ASN1 installation is here: $asn1_install_log "
    (
    $SUDO rm -rf /tmp/asn1c
785
    # GIT_SSL_NO_VERIFY=true git clone https://gitlab.eurecom.fr/oai/asn1c.git /tmp/asn1c
Cedric Roux's avatar
Cedric Roux committed
786
    git clone https://gitlab.eurecom.fr/oai/asn1c.git /tmp/asn1c
787
    cd /tmp/asn1c
Cedric Roux's avatar
Cedric Roux committed
788 789 790
    # better to use a given commit than a branch in case the branch
    # is updated and requires modifications in the source of OAI
    #git checkout velichkov_s1ap_plus_option_group
791
    git checkout f12568d617dbf48497588f8e227d70388fa217c9
792
    autoreconf -iv
793 794 795 796 797 798 799 800 801
    ./configure
    make -j`nproc`
    $SUDO make install
    cd -
    $SUDO ldconfig
    ) > $asn1_install_log 2>&1
}

#################################################
802
# 2. compile
803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830
################################################

install_nas_tools() {
  if [ ! -f .ue.nvram0 ]; then
    echo_success "generate .ue_emm.nvram .ue.nvram"
    ./nvram --gen -c $1 -o $2
  else
    [ ./nvram -nt .ue.nvram0 -o ./nvram -nt .ue_emm.nvram0 ] && ./nvram --gen -c $1 -o $2
  fi

  if [ ! -f .usim.nvram0 ]; then
    echo_success "generate .usim.nvram"
    ./usim --gen -c $1 -o $2
  else
    [ ./usim -nt .usim.nvram0 ] && ./usim --gen -c $1 -o $2
  fi

}


################################
# set_openair_env
###############################
set_openair_env(){
    fullpath=`readlink -f $BASH_SOURCE`
    [ -f "/.$fullpath" ] || fullpath=`readlink -f $PWD/$fullpath`
    openair_path=${fullpath%/cmake_targets/*}
    openair_path=${openair_path%/targets/*}
831
    openair_path=${openair_path%/openair[123]/*}
832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847
    export OPENAIR_DIR=$openair_path
    export OPENAIR1_DIR=$openair_path/openair1
    export OPENAIR2_DIR=$openair_path/openair2
    export OPENAIR3_DIR=$openair_path/openair3
    export OPENAIR_TARGETS=$openair_path/targets
}

################################
# Function to killall the subprocesses when Ctrl-C Key is hit
###############################
function handle_ctrl_c(){
CURPID=$$
ppid=$$
arraycounter=1
echo_info "** Trapped CTRL-C. Killing all subprocesses now..."
echo_info "** Calling sync now..."
848
sync
849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865
while true
do
        FORLOOP=FALSE
        # Get all the child process id
        for i in `ps -ef| awk '$3 == '$ppid' { print $2 }'`
        do
                if [ $i -ne $CURPID ] ; then
                        procid[$arraycounter]=$i
                        arraycounter=`expr $arraycounter + 1`
                        ppid=$i
                        FORLOOP=TRUE
                fi
        done
        if [ "$FORLOOP" = "FALSE" ] ; then
           arraycounter=`expr $arraycounter - 1`
           ## We want to kill child process id first and then parent id's
           while [ $arraycounter -ne 0 ]
866
           do
867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897
             echo "first we send ctrl-c to program"
             $SUDO kill -INT "${procid[$arraycounter]}"
             sleep 5
             echo "Now we force kill if that didn't work"
             $SUDO kill -9 "${procid[$arraycounter]}" >/dev/null
             arraycounter=`expr $arraycounter - 1`
           done
         exit
        fi
done
}


# get from http://www.linuxjournal.com/content/validating-ip-address-bash-script
validate_ip() {

local  ip=$1
local  stat=1

if [[ $ip =~ ^[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}$ ]]; then
    OIFS=$IFS
    IFS='.'
    ip=($ip)
    IFS=$OIFS
    [[ ${ip[0]} -le 255 && ${ip[1]} -le 255 \
        && ${ip[2]} -le 255 && ${ip[3]} -le 255 ]]
    stat=$?
fi

return $stat
}