Merge remote-tracking branch 'internal/T-tracer-extract-input-subframe' into develop_integration_w34

Parameters are for Eurecom internal use.

How to use:

1 - compilation of softmodem:
  ./build_oai --eNB -t ETHERNET

2 - compilation of mobipass driver:
  cd cmake_targets/lte_build_oai/build
  make oai_mobipass
  ln -sf liboai_mobipass.so liboai_transpro.so

3 - configuration:
  edit the configuration file, set "node_timing" to
  "synch_to_mobipass_standalone"
  that is, have the line:
    node_timing               = "synch_to_mobipass_standalone";

4 - run:
  run as usual: sudo ./lte-softmodem -C <configuration file>

These steps take time and are not necessary.

This program extracts a given subframe from a recorded trace.

protobuf-c does not compile anymore.

Let's handle this a bit better.

We now install protobuf and protobuf-c only for the
flexran agent. That is, if you want to use the flexran
agent, you need to install protobuf/protobuf-c and
you do it this way:

  ./build_oai -I -a

(you add -a)

Other targets don't need protobuf nor protobuf-c, so
it's not installed by the -I command of build_oai,
unless you pass -a with -I.

Also, we now use protobuf 3.3.0, not 2.6.1. The code
has been adapted, a quick test seems to indicate that
the system works, but it has not been intensively tested.

several problems were present:
- there was no comma after "ue0_trx_write_ns_missing" in the array
  eurecomVariablesNames;
  comma was put, and also commas for the last element in the array,
  which doesn't hurt and will prevent future problems
- bad order of values in eurecomVariablesNames, which
  was different from the enum vcd_signal_dump_variables;
  order was checked and fixed
- strange/wrong use of VCD_SIGNAL_DUMPER_MODULE_END/LAST;
  the whole logic was removed/simplified

Summary of changes:
- UE: new thread idx
- UE: Pdcch optim
- UE: slot0 slot1 parallelization
- bugfixes for RLC AM (see gitlab issue 250)
- fix bug "unknown UE_id for rnti"

Note: due to the new UE threading architecture,
oaisim and the phy simulators may not work properly
anymore. Adaptation in the code has been done, automatic
tests seem to pass, but it may not be enough.

See merge request !215

With the new threading architecture of the UE dlsim
(and others) does not work properly anymore.

When looking at the scope, you see a difference
in PDSCH LLR display. The end is always 0 where
in the current develop branch (tag 2017.w25) it's not.

This commit attempts to fix it.

We still don't have the same behavior as in 2017.w25.
I disabled channel simulation (so that UE RX = eNB TX)
and I have one error where in 2017.w25 I have zero.
For example, here comes the output of a run of "./dlsim":

**********************SNR = 0.000000 dB (tx_lev 51.000000)**************************
Errors (1(0)/1000 0/1 0/0 0/0), Pe = (1.000000e-03,0.000000e+00,-nan,-nan), dci_errors 0/1001, Pe = 0.000000e+00 => effective rate 99.900100, normalized delay 0.001472 (1.001000)

And in 2017.w25 we have (with the same hack to disable
channel simulation):

**********************SNR = 0.000000 dB (tx_lev 51.000000)**************************
Errors (0(0)/1000 0/0 0/0 0/0), Pe = (0.000000e+00,-nan,-nan,-nan), dci_errors 0/1000, Pe = 0.000000e+00 => effective rate 100.000000, normalized delay 0.001471 (1.000000)

There may be a problem somewhere. Or there was one before and we should
have had one error and the new UE architecture fixed things and now
it's as it has to be. Hard to say at this point...

When looking at the scope we quickly see some zeros for the PDSCH
LLR, at the begining this time, not at the end. This is just when
the GUI appears and then all is fine, so this seems to be for the
first frame only. In 2017.w25 this does not happen.

With the current implementation of oaisim
(rxdata and channel simulation), we cannot
call trx_read_func on a dummy buffer. The
code will actually modify the rxdata buffers
of the UE.

This is has to be rewritten properly. In the
meantime, let's introduce a simple hack. The
idea of the read at this point is to wait for
the synch to finish and not lose samples from
the hardware in the real UE. In the simulator,
as it is today, we can simply sleep until the
synch code has finished its work.

In case of oaisim, dl_phy_sync_success has to be called
by initial_sync, as it used to be.

We introduce an #if OAISIM, this is not elegant, but will
do it for the moment.

Merge remote-tracking branch 'origin/bugfix-258-unknown-ue-id-for-rnti' into develop_integration_w30

This bug happens when we detect uplink failure for one UE.
In this case, a DCI format 1A is sent to the UE to ask it
to do random acces.

The way this DCI is generated was not compatible with how
the software is organized. It was expected that the DCI are
added (with add_ue_spec_dci and add_common_dci) in a very
specific order: first all DCIs in common space are added
(with add_common_dci) then all DCIs in UE specific space
are added (with add_ue_spec_dci).

The problem was that the DCI format 1A DCI sent to the UE
for it to do random access is added (with add_ue_spec_dci)
before the DCIs in common space.

That totally messed up the logic in add_common_dci and
add_ue_spec_dci.

The solution is to get rid of Num_common_dci and Num_ue_spec_dci,
replace those two counters by only one (Num_dci) and add
"search_space" in the dci_alloc structure to be used later by
the function "allocate_CCEs" when calling "get_nCCE_offset".

The software had to be adapted to the new variables, everywhere.

I am not sure that the simulators work. It seems that some
of them didn't use Num_common_dci and Num_ue_spec_dci to
decide on what space (common or UE specific) to put the DCI,
but relied on the rnti (comparing with SI_RNTI). To be tested
properly.

The modified simulators are:
  - openair1/SIMULATION/LTE_PHY/dlsim.c
  - openair1/SIMULATION/LTE_PHY/dlsim_tm4.c
  - openair1/SIMULATION/LTE_PHY/dlsim_tm7.c
  - openair1/SIMULATION/LTE_PHY/framegen.c
  - openair1/SIMULATION/LTE_PHY/pdcchsim.c
  - openair1/SIMULATION/LTE_PHY/syncsim.c

Conflicts:
	targets/RT/USER/lte-softmodem.c