add missing file for adjust synch

openair1/PHY/NR_UE_ESTIMATION/nr_adjust_synch_ue.c

+/*
+ * Licensed to the OpenAirInterface (OAI) Software Alliance under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.
+ * The OpenAirInterface Software Alliance licenses this file to You under
+ * the OAI Public License, Version 1.1  (the "License"); you may not use this file
+ * except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *      http://www.openairinterface.org/?page_id=698
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *-------------------------------------------------------------------------------
+ * For more information about the OpenAirInterface (OAI) Software Alliance:
+ *      contact@openairinterface.org
+ */
+
+#include "PHY/types.h"
+#include "PHY/defs_nr_UE.h"
+#include "PHY/NR_UE_ESTIMATION/nr_estimation.h"
+#include "PHY/impl_defs_top.h"
+//#include "openair2/LAYER2/MAC/mac_proto.h"
+
+#include "common/utils/LOG/vcd_signal_dumper.h"
+
+#define DEBUG_PHY
+
+// Adjust location synchronization point to account for drift
+// The adjustment is performed once per frame based on the
+// last channel estimate of the receiver
+
+void nr_adjust_synch_ue(NR_DL_FRAME_PARMS *frame_parms,
+                      PHY_VARS_NR_UE *ue,
+                      module_id_t eNB_id,
+					  uint8_t subframe,
+                      unsigned char clear,
+                      short coef)
+{
+
+  static int max_pos_fil = 0;
+  static int count_max_pos_ok = 0;
+  static int first_time = 1;
+  int temp = 0, i, aa, max_val = 0, max_pos = 0;
+  int diff;
+  short Re,Im,ncoef;
+
+  VCD_SIGNAL_DUMPER_DUMP_FUNCTION_BY_NAME(VCD_SIGNAL_DUMPER_FUNCTIONS_UE_ADJUST_SYNCH, VCD_FUNCTION_IN);
+
+  ncoef = 32767 - coef;
+
+//#ifdef DEBUG_PHY
+  LOG_D(PHY,"AbsSubframe %d.%d: rx_offset (before) = %d\n",ue->proc.proc_rxtx[0].frame_rx%1024,subframe,ue->rx_offset);
+//#endif //DEBUG_PHY
+
+
+  // we only use channel estimates from tx antenna 0 here
+  for (i = 0; i < frame_parms->nb_prefix_samples; i++) {
+    temp = 0;
+
+    for (aa=0; aa<frame_parms->nb_antennas_rx; aa++) {
+      Re = ((int16_t*)ue->common_vars.common_vars_rx_data_per_thread[ue->current_thread_id[subframe]].dl_ch_estimates_time[eNB_id][aa])[(i<<1)];
+      Im = ((int16_t*)ue->common_vars.common_vars_rx_data_per_thread[ue->current_thread_id[subframe]].dl_ch_estimates_time[eNB_id][aa])[1+(i<<1)];
+      temp += (Re*Re/2) + (Im*Im/2);
+    }
+
+    if (temp > max_val) {
+      max_pos = i;
+      max_val = temp;
+    }
+  }
+
+  // filter position to reduce jitter
+  if (clear == 1)
+    max_pos_fil = max_pos;
+  else
+    max_pos_fil = ((max_pos_fil * coef) + (max_pos * ncoef)) >> 15;
+
+  // do not filter to have proactive timing adjustment
+  max_pos_fil = max_pos;
+
+  if(subframe == 1)
+  {
+      diff = max_pos_fil - (frame_parms->nb_prefix_samples>>3);
+
+      if ( abs(diff) < SYNCH_HYST )
+          ue->rx_offset = 0;
+      else
+          ue->rx_offset = diff;
+
+      if(abs(diff)<5)
+          count_max_pos_ok ++;
+      else
+          count_max_pos_ok = 0;
+          
+          printf("adjust sync count_max_pos_ok = %d\n",count_max_pos_ok);
+
+      if(count_max_pos_ok > 10 && first_time == 1)
+      {
+          first_time = 0;
+          ue->time_sync_cell = 1;
+          if (ue->mac_enabled==1) {
+              LOG_I(PHY,"[UE%d] Sending synch status to higher layers\n",ue->Mod_id);
+              //mac_resynch();
+              //dl_phy_sync_success(ue->Mod_id,ue->proc.proc_rxtx[0].frame_rx,0,1);//ue->common_vars.eNb_id);
+              ue->UE_mode[0] = PRACH;
+          }
+          else {
+              ue->UE_mode[0] = PUSCH;
+          }
+      }
+
+      if ( ue->rx_offset < 0 )
+          ue->rx_offset += FRAME_LENGTH_COMPLEX_SAMPLES;
+
+      if ( ue->rx_offset >= FRAME_LENGTH_COMPLEX_SAMPLES )
+          ue->rx_offset -= FRAME_LENGTH_COMPLEX_SAMPLES;
+
+
+
+      #ifdef DEBUG_PHY
+      LOG_I(PHY,"AbsSubframe %d.%d: ThreadId %d diff =%i rx_offset (final) = %i : clear %d,max_pos = %d,max_pos_fil = %d (peak %d) max_val %d target_pos %d \n",
+              ue->proc.proc_rxtx[ue->current_thread_id[subframe]].frame_rx,
+              subframe,
+              ue->current_thread_id[subframe],
+              diff,
+              ue->rx_offset,
+              clear,
+              max_pos,
+              max_pos_fil,
+              temp,max_val,
+              (frame_parms->nb_prefix_samples>>3));
+      #endif //DEBUG_PHY
+
+      VCD_SIGNAL_DUMPER_DUMP_FUNCTION_BY_NAME(VCD_SIGNAL_DUMPER_FUNCTIONS_UE_ADJUST_SYNCH, VCD_FUNCTION_OUT);
+  }
+}