After removing RA.crnti, there is no need to use a separate function
nr_generate_Msg3_dcch_dtch_response() to generate Msg.4 (yes, the
function mentions Msg3 but it does Msg3 response == Msg.4).

Also, using nr_generate_Msg4() has the advantage that it waits until we
have the reconfiguration available in RLC to be sent to the UE. Finally,
we can delete the old nr_generate_Msg3_dcch_dtch_response() as we don't
need it anymore.

The RA.crnti field is marked as being used by NSA mode, but it is not.
OTOH, it is used in the case of RA with Msg.3 with C-RNTI MAC CE. The
latter does not necessarily need it, though, as we can change the RNTI
of the RA process when we receive C-RNTI MAC CE.

This introduces a slight complication, though, as we cannot remove the
MAC UE Context (generated when receiving Msg.3) directly when parsing
the C-RNTI MAC CE. Previously, we had both rnti and crnti in the RA
struct, and when sending Msg.4 after Msg.3 with C-RNTI MAC CE, we would
remove the UE context (this is changed in the next commit). Therefore,
we employ nr_mac_trigger_release_timer() which releases the UE after
60ms, circumventing this complication.

The RRC should not trigger RLC bearer establishment: this should be done
only via F1, and in the remaining code (removed here), this principle
was violated.

Further, this code was doubly wrong, as it used the CU UE ID for the
RLC, setting up bearers with IDs 1,2,3 etc instead of the RNTI.

The MAC_NR target is not needed; every dependent target also links
L2_NR. Therefore, this target just creates double compilation. We can
remove it without problems.

integration_2023_w32

See merge request oai/openairinterface5g!2293

* !2061 Rel16 NR PRS improvements
* !2113 handle TDD pattern2 at UE
* !2266 Use cmake3 command if on RHEL
* !2287 Initialize OAIgraph before usage
* !2285 Fix alignment of Tpool user data to 32 bytes
* !2284 USRP driver: Make it compile for UHD < 4.0.0
* !2214 Use F1 Internally: switch to CU UE ID in CU

Via the include of the logging system, the ethernet transport
library implicitly depends on T. Hence, link T into
oai_eth_transpro.

This commit repairs the reestablishment after the introduction of the CU
UE ID in the CU, different from the DU UE ID. Now, the CU uses an
identifier different from the RNTI, used in the MAC, to refer to UEs.

To repair the reestablishment, a number of changes needed to be
introduced:

- Handle old_gNB_DU_UE_id in MAC

The MAC handles the old_gNB_DU_UE_id field in the DL RRC Message. The
commit adds encoding/decoding of the field. The MAC will drop the old
UE, but retain the CellGroup of the corresponding UE(!). Because a UE
releases the spCellGroup on reestablishment, the MAC does the same; it
needs to reapply the old configuration after a reconfiguration. For the
latter, introduce new variables to keep a "future" CellGroupConfig to be
applied (reconfigCellGroup) and a flag (expect_reconfiguration) that
applies the CellGroupConfig if a DL RRC Message transfer on DCCH, which
is assumed to be the reconfiguration.

- Add RNTI change in RLC

The RLC needs to reuse the old UE context. Hence, we simply change the
RNTI in the old context, and delete the new one.

- No PDCP UE ID change

The previous implementation of the PDCP used the RNTI; hence, the ID
needed to be switch (as above for the RLC). Since the PDCP now also uses
the CU UE ID, no identifier change is needed, and we remove all
corresponding code.

- No MAC modifications/update from CU

As foreseen by the spec, the CU does not modify or change the
cellGroupConfig in the RRC during reestablishment. This change will be
generalized in the future to all of the RRC.  Also, the
nr_rrc_mac_remove_ue() function has been removed: the MAC handles any UE
changes autonomeously, without being triggered from the RRC explicitly.

- Remove reestablish_rnti_map

The RRC does not use RNTIs for UE identification. Hence, a
reestablish_rnti_map to link two UEs to each other is not necessary
anymore.

After a reestablishment, the PDCP sequence number counters have to be
reset. Implement an API to allow the RRC to reset the sequence numbers
for a particular UE in the case of reestablishment

Plugin can trigger reestablishment (on DU)
and show counters of reestablishment (on CU)

The RRC gives its own RRC UE ID. It won't intervene if DUs assign the same RNTI to different UEs: it simply does not care what the DUs do with the RNTI.

- Use the same CU-UP in E1 as in CU-CP: we don't have a separate entity
  to allocate IDs, and we just use the same as the CU-CP
- Correct gNB CU-UP/CP UE IDs in E1AP message types to 32bit
- Set CU UP UE ID explicitly for clarity
- Remove RNTI from E1 messages, E1 does not know what an RNTI is

The UE had a list of known UEs. With the introduction of a separate
module for F1 UE ID handling that is also used in monolithic (to
separate CU UE ID from DU UE ID), this functionality is not needed, and
deleted in this commit.

Previously, the F1AP handler called various functions directly, instead
of sending an ITTI message to the RRC thread. This has two drawbacks:
- it can lead to data races if the RRC task uses functionality that is
  being accessed by the F1 task through this function
- no homogeneity: all other handlers send an ITTI message, so this one
  should too

- The CU/DU UE ID is used in DL RRC Message Transfer
- Note: The CU UE ID currently is still the RNTI
- on every DL RRC Message, the DU verifies that the UE exists
- Refactor RRC: common function to forward protected SRB PDUs

The RRC uses gNB_ue_ngap_id as its primary ID; the following commits
will introduce the usage of the (F1) gNB CU UE ID. This commits renames
the gNB_ue_ngap_id to rrc_ue_id to better reflect its usage as the RRC's
primary UE ID.

It will be used as the NGAP and F1 (CU) UE IDs.